Abstract:Twin-screw granulation is a promising wet granulation technique for the continuous manufacturing of pharmaceutical solid dosage forms. A twin screw granulator displays a short residence time. Thus, the solid-liquid mixing must be achieved quickly by appropriate arrangement of transport and kneading elements in the granulator screw allowing the production of granules with a size distribution appropriate for tableting. The distribution of residence time and granulation liquid is governed by the field conditions (such as location and length of mixing zones) in the twin-screw granulator, thus contain interesting information on granulation time, mixing and resulting sub-processes such as wetting, aggregation and breakage. In this study, the impact of process (feed rate, screw speed and liquid-to-solid ratio) and equipment parameters (number of kneading discs and stagger angle) on the residence time (distribution), the granulation liquid-powder mixing and the resulting granule size distributions during twin-screw granulation were investigated. Residence time and axial mixing data was extracted from tracer maps and the solid-liquid mixing was quantified from moisture maps, obtained by monitoring the granules at the granulator outlet using near infra-red chemical imaging (NIR-CI). The granule size distribution was measured using the sieving method. An increasing screw speed dominantly reduced the mean residence time. Interaction of material throughput with the screw speed and with the number of kneading discs led to most variation in the studied responses including residence time and mixing capacity. At a high screw speed, granulation yield improved due to high axial mixing. However, increasing material throughput quickly lowers the yield due to insufficient mixing of liquid and powder. Moreover, increasing liquid-to-solid ratio resulted in more oversized granules, and the fraction of oversized granules further increased at higher throughput. Although an increasing number of kneading discs was found to be critical for achieving a uniform distribution of the granulation liquid, the granulation performance was hampered due to insufficient solid-liquid mixing capacity of the current kneading discs which is essential for wet granulation. Thus, a balance between material throughput and screw speed should be strived for in order to achieve a specific granulation time and solid-liquid mixing for high granulation yield. Additionally, more efforts are needed both in modification of the screw configuration as well as the geometry of the mixing elements to improve the mixing capacity of the twin-screw granulator. The results from the current experimental study improved the understanding regarding the interplay between granulation time and the axial and solid-liquid mixing responsible for the granulation performance in twin-screw wet granulation.

Influence of the centrifugal granulating process on the properties of layered pellets

Effects of Process Variables on the Size, Shape, and Surface Characteristics of Microcrystalline Cellulose Beads Prepared in a Centrifugal Granulator

Investigation of the Electrokinetic Potential of Granules and Optimization of the Pelletization Method Using the Quality by Design Approach

Application of Near-Infrared Spectroscopy Combined with Design of Experiments for Process Development of the Pulsed Spray Fluid Bed Granulation Process

An Evaluation of Process Variables in wet Granulation

Application of Definitive Screening Design to Quantify the Effects of Process Parameters on Key Granule Characteristics and Optimize Operating Parameters in Pulsed-Spray Fluid-Bed Granulation

Mechanistic understanding of the effects of process and design parameters on the mixing dynamics in continuous twin-screw granulation

Influence of process conditions on the product properties in a continuous fluidized bed spray granulation process

Impact of non-binder ingredients and molecular weight of polymer binders on heat assisted twin screw dry granulation

Studies on the Influence of High-Shear Granulation Process on the Compressibility of Microcrystalline Cellulose

Linking granulation performance with residence time and granulation liquid distributions in twin-screw granulation: An experimental investigation

Influence of Polymer Film Thickness on Drug Release from Fluidized Bed Coated Pellets and Intended Process and Product Control

Effects of Manufacturing Process Variables on the Tablet Weight Variation of Mini-tablets Clarified by a Definitive Screening Design

Adapting the process conditions and performance in planetary roller melt granulation (PRMG) via the planetary spindle number

Melt granulation in fluidized bed: a comparative study of spray-on versus in situ procedure

Influence of separation properties and processing strategies on product characteristics in continuous fluidized bed spray granulation

The influence of mechanical processing of dry powder inhaler carriers on drug aerosolization performance

Rotational Molding of Poly(lactic acid): Effect of Polymer Grade and Granulometry

Influence of the porosity of cushioning excipients on the compaction of coated multi-particulates

Influence of processing methods on physico-mechanical properties of Ibuprofen/HPC-SSL formulation

The role of adding nanoparticles and surfactant to the enzyme liquid binder in fluidized bed granulation process