Abstract:Abstract Austenitic stainless steel 316 has very high mechanical properties and corrosion resistance. This type of steel is widely used both in the nuclear and non-nuclear industries. In the nuclear industry, SS316 is used as a cladding material for uranium fuel due to its good corrosion and mechanical properties, and also low neutron absorption cross-section. In the Center for Nuclear Fuel Technology (PTBBN BATAN), it is used as material for the container of nuclear waste that is to be stored on Temporary Storage Installation of Spent Fuel (KHIPSB3 BATAN). SS316 is used as material for can to contain high-activity solid waste from the testing activity in Radiometallurgy Installation (IRM BATAN). The lid of the container is sealed with the GTAW welding process in order to tightly contain the solid waste. The main problem with the heat treatment and welding process of austenitic stainless steel is the occurrence of sensitization in a temperature range of 500-800°C. Therefore fully electrochemical analysis of SS316 stainless steel in various mediums has been conducted. SS 316 specimen was heat-treated to simulate the heat generated by the welding process. Sensitization analysis was conducted with qualitative and quantitative methods by EIS and EPR, and pitting corrosion resistance was by cyclic polarization method. The solution used for EIS and cyclic polarization test was 0 − 3.5% concentration of NaCl, and for EPR test was a mixture of H 2 SO 4 and KSCN. Material characterization before and after corrosion testing was microstructure examination. The result of the corrosion test showed that heat treatment on the temperature range of 500-800°C caused sensitization. The corrosion test curve result showed that a heat treatment temperature of 650°C for 1 hour had the highest activation current. The lowest Rp value for SS316 specimen post heat treatment in 675°C was 69.410 ohm. The welded SS316 specimen had a higher corrosion current than that of the unwelded specimen. The microstructure of the welded specimen showed that there was intergranular corrosion particularly in the HAZ region. The effect of NaCl concentration on the cyclic polarization test showed that the higher the NaCl concentration, the more easily the pitting corrosion. The indication of pitting corrosion occurrence was evaluated by considering the E pit and E rp values. The lower E pit value meant that pitting corrosion was more easily to occur.

Corrosion resistance comparison of various carbon steel in inlet water of heat exchanger’s Kujang ammonia plant

Corrosion rate of low carbon steel in simulated feed water for heat exchanger in ammonia plant

Comparative Study on the Corrosion Behavior of Materials in Heat Recovery Steam Generators for Combined Cycle Power Plant, Based on Sulfuric Acid Concentrations: Carbon Steels vs. Duplex Stainless Steel (UNS S32205)

Corrosion Of Carbon Steel In Typical Water Environments Of Thermal Power Plant

Corrosion Behavior of 16mnr Steel and Welded Joints in High-Temperature Naphthenic Acid

Corrosion Rate Analysis of Steam Boiler Superheater

Laboratory assessment of corrosion rate of carbon steel ground heat exchangers

Ammonia corrosion resistance of surface-treated aluminum materials

Experiment on the Anti-corrosion Property of Chrome Molybdenum Steel Tube in Naphthenic Acid Environment

Corrosion Behavior of Carbon Steel at Typical Positions of an Amine-Based CO2 Capture Pilot Plant

High Temperature Corrosion Resistance of Different Commercial Alloys Under Various Corrosive Environments

A Study of the Corrosion Behaviour of Magnetron-Sputter Deposited Coatings in a Reducing-Sulphidising Atmosphere at 600°C

Corrosion Investigation of Commercially Available Linepipe Steel in CO2 Environment

Corrosion Behavior of Superalloys in High Temperature Gas Cooled Reactor in Impure Helium with Corrosion Time

Corrosion behaviour of 316L stainless steel and anti-corrosion materials in a high acidified chloride solution

An Experimental Investigation on the Relation between Corrosion and Thermohydraulic Behavior in Heat Exchangers for Geothermal Applications

Study on the failure analysis of four metals for anaerobic fermentation reactor based on numerical simulation and electrochemical method

Hot-corrosion resistance of dissimilar AISI 4340 and AISI 304L weldments in the molten salt environment at 600°C

On the resistance of aluminized steel in high temperature water

Comparison of the corrosion of materials in supercritical carbon dioxide, air, and argon environments

Corrosion analysis of post-heat treatment and post-weld SS316 with electrokinetic reactivation and cyclic polarization method