Abstract:Masonry was the most used material during the last centuries to build constructions. Most of the existing masonry structures (buildings, bridges, etc.) were built without considering some important structural considerations that are important nowadays. Moreover, due to factors such as the increasing of service loads, materials aging, structural damage, etc., the existing masonry structures require strengthening interventions. The definition of optimal strengthening strategies using traditional and innovative materials is still an important issue of the scientific research. In fact, during the last decade, many researchers focused their attention studying innovative composites materials, such as fiber-reinforced polymers and fiber-reinforced cementitious matrix composites, for the strengthening of existing masonry structures. This research has focused on aspects such as the bond behavior between the substrate and the composite materials, the structural behavior of the strengthened masonry and concrete structures, and the compatibility and reversibility of these materials when bonded to existing substrates. In this study, the bond behavior of a composite material known as steel fiber-reinforced mortar (SFRM), recently used as for the strengthening of existing structures, applied onto masonry structures is analyzed experimentally and numerically. First, the material is characterized experimentally with the aim of getting insight on its behavior and applicability when applied as an innovative technique for the strengthening of masonry and to obtain mechanical parameters required for the numerical models. Mechanical properties of the SFRM studied included flexural and compressive strength, tensile strength, and residual flexural strength. The SFRM bond behavior on masonry substrates was evaluated by means of double shear lap tests. In addition, the experimental tensile and bond behavior of the SFRM is studied numerically through finite-element models validated using the results obtained during the experimental tests. Results show that if an adequate bonded length is provided, the SFRM can fully develop its tensile strength as detachment from the substrate is not observed.

Nonlinear Behavior of a Masonry Subassemblage Before and After Strengthening with Inorganic Matrix-Grid Composites

Dynamic Progressive Collapse Response of Multi-Storey Frame Structures with Masonry Infills

In-Plane Lateral Response of a Full-Scale Masonry Subassemblage with and without an Inorganic Matrix-Grid Strengthening System

Effectiveness of FRCM Reinforcement Applied to Masonry Walls Subject to Axial Force and Out-Of-Plane Loads Evaluated by Experimental and Numerical Studies

Nonlinear finite and discrete element simulations of multi-storey masonry walls

Nonlinear Static Analysis On Masonry Wall Strengthened With Reinforced Mortar Overlay

Strengthening with Near Surface Mounted Reinforcement: Structural and Fire Behavior

Combined Strengthening Techniques to Improve the Out-of-Plane Performance of Masonry Walls

Modelling of unreinforced periodic masonry panels tested under two-way bending via a non-linear discrete homogenized strategy

Strain Monitoring and Crack Detection in Masonry Walls under In-Plane Shear Loading Using Smart Bricks: First Results from Experimental Tests and Numerical Simulations

Numerical and Experimental Investigation on Cyclic Behavior of Masonry Infill Walls Retrofitted with CFRP

Out-of-plane Response of an Innovative Masonry Infill with Sliding Joints from Shaking Table Tests

Bond behavior of steel fiber-reinforced mortar (SFRM) applied onto masonry substrate

Push-over analysis of a rubble full-scale masonry wall reinforced with stainless steel ribbons

Diagonal shear behavior of historic walls strengthened with composite reinforced mortar (CRM)

3D hybrid modelling approach combining the finite and discrete element methods: Validation based on masonry shear wall tests

In-Plane Strengthening Effect of Prefabricated Concrete Walls on Masonry Structures: Shaking Table Test

Macromechanical Failure Criteria: Elasticity, Plasticity and Numerical Applications for the Non-Linear Masonry Modelling

Nonlinear masonry wall analysis of strengthened with high-strength wire cable and polymer mortar

Experimental In-Plane Shear Performance of Masonry Infill Walls Assembled with Cementitious Matrix–Grid Composites

Numerical Simulation of the Failure Process of Unreinforced Masonry Walls Due to Concentrated Static and Dynamic Loading