Abstract:Purpose This study aims to form composite solid lubricant coatings on the surface of bearing steel, which can significantly improve the tribological properties of thrust cylindrical roller bearings (TCRBs). Phosphating films possess microscopic porosity that typically needs to be sealed with oil, grease or wax. Due to its unique crystal structure, the phosphating film itself also exhibits a certain degree of lubricity. In this study, solid lubricants are used to fill the pores of the phosphating film. By combining the phosphating film with solid lubricants, lubrication and wear reduction can be achieved. Design/methodology/approach In this study, the surfaces of the shaft washer (WS) and seat washer (GS) were treated with zinc-phosphating. Subsequently, a solid lubricant solution (polytetrafluoroethylene [PTFE], MoS 2 and graphite) was sprayed onto the phosphated samples at concentrations of 1 , 2 and 3 g/L. The porous and adsorptive nature of the phosphating film was used to embed the solid lubricant particles into the film, thus forming a composite lubrication layer containing solid lubricants on the surface of the bearing steel. Findings The addition of solid lubricant materials has shown significant potential in reducing wear losses compared with phosphated samples without such additives. Increasing the amount of solid lubricant added can facilitate the formation of a transfer film, which further enhances the protective properties. However, it is important to note that excessive amounts of solid lubricant material can contribute to seizure, leading to increased wear losses of the cage and a higher average coefficient of friction (ACOF).By spraying a PTFE solution with a concentration of 2 g/L, the lowest ACOF and cage wear loss were achieved, resulting in reductions of 60.5% for the ACOF and 89.4% for the cage wear loss. Similarly, when spraying a graphite solution with a concentration of 3 g/L, the lowest wear losses for GS and WS were observed, with reductions of 51.7% for GS wear loss and 38.9% for WS wear loss. Originality/value The combination of the phosphating film and solid lubricants aims to achieve lubrication and wear reduction, providing a new approach to wear-resistant technology for TCRBs. Peer review The peer review history for this article is available at: https://publons.com/publon/10.1108/ILT-07-2023-0231/

Solid polymer bearings in tribological applications

Polymer composites based on aromatic polyamide and fillers of spherical and layered structure for friction units of high-performance equipment

Researches on Friction Performance of Water-Lubricated Polymer Composite Journal Bearings Based on Experiments

Friction and Wear Performance of Various Polymer Coatings for Journal Bearings under Stop Start Sliding

Resource testing of modified plain bearings for the aviation industry

Tribological evaluation of thermoplastic polyurethane-based bearing materials under water lubrication: Effect of load, sliding speed, and temperature

Polymeric Tribotechnical Composites on the Basis of Polytetrafluoroethylene and Complex Fillers

A review on tribology of polymer composite coatings

Tribological characteristics of polymer materials used for slide bearings

Performance and mechanisms of different tribological thermoplastic composites in sliding contact with steel

Evaluation of Tribological Properties of Polymer Materials Used for Sliding Bearings in Agricultural Machinery

Application of metal-polymer plain bearings for heavily loaded friction angles

Microstructural, mechanical, and tribological properties of a novel hybrid LLDPE/PTFE/x wt.% GNPs for bearing surface applications

Composites for Aerospace Dry Bearing Applications

Revisiting polymer tribology for heavy duty application

Experimental study on the feasibility of alternative materials for tilting pad thrust bearings operating in transition to mixed friction

Synthesis and Tribological Behavior of Bridged Bicyclic Polymers As Lubricants

Tribological and Vibration Properties of Three Different Polymer Materials for Water-Lubricated Bearings

Tribological Behavior of Reinforced PTFE Composites and Un-Reinforced Polyketone-Based Materials against Coated Steel

Estimation of tribotechnical parameters of composite polymer with metal filler

Effect of composite solid lubricant coatings on the tribological performance of thrust cylindrical roller bearings