Abstract:The effects of a minor Zn addition on the mechanical and corrosion properties and microstructure of a high Mg content AlMg alloy containing Er and Zr in the warm-rolled state were studied using tensile test, nitric acid mass loss test (NAMLT), exfoliation corrosion susceptibility test (ASSET), scanning electron microscopy (SEM) and transmission electron microscopy (TEM) techniques. The tensile test results showed that the 0.58 wt% Zn addition to the Al-Mg-Er-Zr alloy increased the yield strength from 297 to 351 MPa and tensile strength from 416 to 445 MPa, but decreased the elongation from 13.3 % to 12.5 %. The NAMLT and ASSET results showed that the two warm rolled alloys were initially in the stabilization state, but the Al-Mg-Er-Zr alloy without Zn added became sensitized severely after the accelerated sensitization annealing (ASA) at 100 °C. The Zn addition improved the intergranular corrosion (IGC) resistance and exfoliation corrosion (EC) resistance significantly. The TEM results showed that, for the Al-Mg-Er-Zr alloy, there were Al 3 (Er,Zr) phase particles in the matrix and β (Al 3 Mg 2 ) phase particles separated from each other at the grain boundary. After the ASA treatment, more β phase particles were precipitated and covered the grain boundary completely. For the Al-Mg-Zn-Er- Zr alloy, another nanoscale T (Al 32 (Mg, Zn) 49 ) phase was precipitated in the matrix, and there were no grain boundary phase particles observed at the grain boundary, because the precipitation of T phase consumed the supersaturated Mg in the matrix, thus suppressing the formation of grain boundary phase particles during the ASA treatment and resulting in a good corrosion resistance. The strengthening effect of the Zn addition was mainly due to the formation of T phase particles during the warm rolling process.

Influence of annealing on electrical resistance and hardness of hot-rolled aluminum alloy sheets containing up to 0.5% Zr

Effect of Zr addition on properties of Al–Mg–Si aluminum alloy used for all aluminum alloy conductor

Influence of Zr on grain orientation, texture, and mechanical properties in hot- and warm-rolled FeCrAl alloys

Effect of Hot Rolling on the Microstructure and Properties of Nanostructured 15Cr ODS Alloys with Al and Zr Addition

Effect of heating rate on the recrystallization behavior and mechanical properties of a cold-rolled Zr702

Effects of Hot Rolling Process Conditions on Microstructure and Mechanical Properties of Hot-rolled Al-Zn-Mg-Cu-Sc-Zr Alloys

Structure and Properties of Ca and Zr Containing Heat Resistant Wire Aluminum Alloy Manufactured by Electromagnetic Casting

Effect of annealing treatment on the microstructure and mechanical properties of warm-rolled Mg–Zn–Gd–Ca–Mn alloys

Enhanced elevated-temperature mechanical properties of hot-rolled Al–Cu alloys: effect of zirconium addition and homogenization

Influence of Zr Microalloying on the Microstructure and Room-/High-Temperature Mechanical Properties of an Al–Cu–Mn–Fe Alloy

Influence of Decreased Temperature of Tensile Testing on the Annealing-Induced Hardening and Deformation-Induced Softening Effects in Ultrafine-Grained Al-0.4Zr Alloy

Effect of cold rolling on microstructure and mechanical properties of pure Zr

Effect of elevated-temperature annealing on microstructureand properties of Cu−0.15Zr alloy

Annealing Behavior of Nanostructured Aluminum Produced by Cold Rolling to Ultrahigh Strains

Influence of Hot Rolling on Microstructure, Corrosion and Mechanical Properties of Mg–Zn–Mn–Ca Alloy

Developing age-hardenable Al-Zr alloy by ultra-severe plastic deformation: Significance of supersaturation, segregation and precipitation on hardening and electrical conductivity

Influence of large amount Zn on mechanical properties and corrosion resistance of 5083 hot rolled aluminum alloy

Effects of Zr on Microstructure and Conductivity of Er Containing Heat-Resistant Aluminum Alloy Used for Wires

Microstructures and Mechanical Properties of a Commercial Pure Zirconium during Rolling and Annealing at Different Temperatures

The influence of Zn addition on the microstructure and mechanical and corrosion properties of warm rolled Al mg alloys containing Er and Zr