Abstract:The magnesium reduction process occurring in a retort as described in Part I is carried out in a refractory brick coal-fired furnace. It is considered that the thermal-flow inside the furnace has an important effect on the heat transfer and reduction of the reactive compound in the retort. In this paper, a comprehensive two-dimensional unsteady model was developed in combination of the magnesium reduction model put forward in Part I with the conventional gas-particle turbulent flow and combustion models. The set of equations was solved by the time-marching method. The prediction revealed the flow characteristics and temperature distribution in the furnace, and the magnesium reduction rate distribution in the retort. Variation of the total magnesium reduction rate with the time was also presented, which is useful for the design and operation of the magnesium reduction system. NOMENCLATURE cp Effective specific heat capacity of the reactant Cp Coal particle specific heat capacity Fd Drag force Fg Gravitational force mp Coal particle mass Qc Convective heat transfer between particle and gas phase Qm Coal combustion heat Qr Radiative heat transfer between particle and gas phase Sr Reaction source term Sφ Source term in Eq. (4) Sφp Source term representing the interaction between coal particle and gas phase in Eq. (4) Tp Coal particle mass up Coal particle velocity u Gas velocity ρ Effective density λ Effective thermal conductivity φ Universal variable in Eq. (4) Γφ Generalize diffusion coefficient in Eq. (4) INTRODUCTION The magnesium production process is carried out in a traditional coal-fired furnace, as shown in Figure 1 (Xu, 2003). Several retorts(5~11) are horizontally placed in the upper and lower rows with a staggered layout in the refractory brick furnace, which are heated by high temperature flue gas(1200~1250°C) from the combustion chamber arranged symmetrically on two sides of the furnace. The magnesium reduction process occurs in the retort. The high temperature flue gas flows out via the outlets at the bottom of the furnace to preheat the inlet air. Figure 1: Cross-section schematic diagram of coal-fired furnace for magnesium production In Part I (Li et al., 2009), we established the magnesium reduction model in the retort according to the actual physical process, and analyzed in detail the behavior of performance of the magnesium reduction process, such as temperature distribution, magnesium reduction rate and heat absorption power, with the time. The influence of heating temperature on the magnesium reduction rate and the heat absorption power was also investigated. However, the heat transfer occurred on the surface of the retort placed in the furnace involves not only the heat conduction but also the convective and radiative heat transfer. Therefore, the objective of this paper is to develop a comprehensive unsteady model in combination with the magnesium reduction model put forward in Part I and with the conventional coal combustion models, and to investigate the effect of thermal-flow field on the performance of the magnesium reduction process in terms of temperature and reduction rate profiles in the retort, and the variation of total reduction rate with the time.

Numerical Study of Magnesium Production by Pidgeon Process and Pre-prepared Pellets Silicothermic Process: Comparison of Heat Transfer

Review on the Silicothermic Process for Primary Magnesium Production

Thermal Decomposition Kinetics of Dolomite in Pre-prepared Pellets for Magnesium Production

Experimental Study of Magnesium (Mg) Production by an Integrated Calcination and Silicothermic Reduction Short Process

Numerical study of magnesium (Mg) production by the Pidgeon process: Impact of heat transfer on Mg reduction process

Magnesium Production from Calcined Dolomite via the Pidgeon Process

Experimental and Numerical Studies on Heat Transfer Enhancement in the Silicothermic Reduction Process

Kinetics of extracting magnesium from prefabricated pellets by silicothermic process under flowing argon atmosphere

Producing Pure Magnesium Through Silicothermic Under the Atmospheric Pressure

Novel Efficient Reduction Route for Magnesium Production Using Silicothermic Process

Reaction characteristics of magnesium production under argon flow by silicothermic reduction and numerical simulation of argon entrainment process

High Silica Dolomite Pidgeon Smelt Magnesium Experiment

Distribution of impurities in magnesium via silicothermic reduction

Smelting Magnesium Metal using a Microwave Pidgeon Method

Thermodynamic Analysis and Processing Evaluation of Magnesium Preparation by Thermal Reduction Method

Producing High Purity Magnesium (99.99%) Directly by Pidgeon Process

Numerical simulation of magnesium production by the pidgeon process part ii : coupling of the magnesium reduction in the retorts with the surrounding thermal-flow fields in a coal-fired furnace

Numerical simulation of gas-solid heat transfer and moisture evaporation process in preheating shaft kiln for ferromagnesium pellets

Investigation on the Effective Thermal Conductivity of Typical Pidgeon Process Briquette with a Combined Model

Numerical Investigation of Gas-Solid Heat Transfer Process and Parameter Optimization in Shaft Kiln for High-Purity Magnesia

Numerical Analysis of the Gas − Solid Heat Transfer Characteristics of a Lightly Calcined MgO Fluidized-bed Roaster