Abstract:Copper die-casting die steel is usually used in severe rugged environment. Liquid metal flows with high temperature and high pressure during injection and provides rapid filling of the die cavity. The copper die-casting steel should has excellent combination of the properties of high toughness, wear resistance, hardness, thermal fatigue resistance, oxidation resistance and corrosion resistance at high temperature for the cavity surface of die-casting die suffers high pressure, scour, erosion and thermal shock. A new kind of copper alloy die-casting die steel with pure austenitic matrix was conducted in this work, wherein the boride with high thermal stability and high hardness distributes in the austenitic matrix. The mechanical properties of copper alloy die-casting die steel at high temperature of 850 degrees C were studied using dynamic thermal-mechanical simulation testing machine. The thermal fatigue behavior of die steel at room temperature to 800 degrees C was performed using self-restraint Uddeholm thermal fatigue test method, and the depth extension status Of surface thermal fatigue cracks and cross-sectional cracks in die steel thermal fatigue specimens was measured using stereo microscope and SEM. The effects of B content on the mechanical properties at room temperature and high temperature and on the thermal fatigue resistance were evaluated. The experimental results showed that boride distributes in austenitic matrix in the form of M2B-type boride (M represents Fe, Cr or Mn) after adding B in the tested steels, and the comprehensive performances of steel at high temperatures were effectively improved, the hardness of the steel at room temperature increased from 200 HV to 302 HV, the tensile yield strength at 850 degrees C increased from 144.3 MPa to 190.3 MPa, and the compressive yield strength increased from 139.7 MPa to 167.9 MPa. Evaluation of the degree of heat checking on 300 cyc of thermal fatigue testing at room temperature to 800 degrees C showed that the die steel containing B was rating 2-3, much better than rating 7 similar to 8 of electroslag remelting ESR-H13 steel for comparison, which mainly because the thermal fatigue cracks were blunted or deflected by boride, and then the cracks spread as scattering shapes was avoided.

Effect of the Testing Temperature on the Impact Property of a Multilayered Soft–Hard Copper–Brass Block

Effect of cryogenic impact deformation and subsequent annealing on microstructure and microhardness of pure copper

Effect of High Temperature-High Pressure Treatment on Microstructure and Mechanical Properties of Cu-Cr Alloy

An Evaluation of the Impact Effect on the Surface Microstructure and Its Induced Temperature Changes during Ultrasonic-Assisted Micro-Forging

Effect of Pretreatment and Cryogenic Temperatures on Mechanical Properties and Microstructure of Al-Cu-Li Alloy

EFFECTS OF B ON HIGH TEMPERATURE MECHA-NICAL PROPERTIES AND THERMAL FATIGUE BEHAVIOR OF COPPER DIE-CASTING DIE STEEL

Effect of Temperature on the Mechanical Properties, Conductivity, and Microstructure of Multi-layer Graphene/Copper Composites Fabricated by Extrusion

Microstructures and mechanical properties of pure copper manufactured by high-strength laser powder bed fusion

A micromechanical study of heat treatment induced hardening in α-brass

The impact of interfacial characteristics on the interfacial properties of 316 L/CuSn10 multi-material manufactured by laser powder bed fusion

Effect of lap configuration on the microstructure and mechanical properties of dissimilar ultrasonic metal welded copper-aluminum joints

Experimental Study on Low-Temperature Mechanical Properties of S30408 Welded Joints

Testing the Impact Resistance of Thick Structural Steel Plate at Low Temperatures

Effect of Casting Temperature on the Microstructure and Mechanical Properties of Cu-10Pb-10Sn/42CrMoS4 Bimetallic Hydraulic Cylinder Block

Effect of annealing temperature on microstructure and tensile properties of copper/aluminum composite thin strip

Effect of heat treatments on microstructure, mechanical and electrical properties of Cu–Cr–Zr alloy manufactured by laser powder bed fusion

Investigation of the adhesive contact between a diamond indenter and single-Crystal copper substrate at low temperatures

Effect of atomic diffusion on interfacial heat transfer and tensile property of copper/aluminum composites

Experimental Study of the Microhardness and Microstructure of a Copper Specimen Using the Taylor Impact Test

Effect of Copper Content and Heat Treatment Schedules on Mechanical Properties, Cold Resistance, and Microstructural Constituent Morphology in Precipitation-Hardened Steel

Significant mechanical softening of copper under coupled electric and magnetic stimuli