Abstract:Copper die-casting die steel is usually used in severe rugged environment. Liquid metal flows with high temperature and high pressure during injection and provides rapid filling of the die cavity. The copper die-casting steel should has excellent combination of the properties of high toughness, wear resistance, hardness, thermal fatigue resistance, oxidation resistance and corrosion resistance at high temperature for the cavity surface of die-casting die suffers high pressure, scour, erosion and thermal shock. A new kind of copper alloy die-casting die steel with pure austenitic matrix was conducted in this work, wherein the boride with high thermal stability and high hardness distributes in the austenitic matrix. The mechanical properties of copper alloy die-casting die steel at high temperature of 850 degrees C were studied using dynamic thermal-mechanical simulation testing machine. The thermal fatigue behavior of die steel at room temperature to 800 degrees C was performed using self-restraint Uddeholm thermal fatigue test method, and the depth extension status Of surface thermal fatigue cracks and cross-sectional cracks in die steel thermal fatigue specimens was measured using stereo microscope and SEM. The effects of B content on the mechanical properties at room temperature and high temperature and on the thermal fatigue resistance were evaluated. The experimental results showed that boride distributes in austenitic matrix in the form of M2B-type boride (M represents Fe, Cr or Mn) after adding B in the tested steels, and the comprehensive performances of steel at high temperatures were effectively improved, the hardness of the steel at room temperature increased from 200 HV to 302 HV, the tensile yield strength at 850 degrees C increased from 144.3 MPa to 190.3 MPa, and the compressive yield strength increased from 139.7 MPa to 167.9 MPa. Evaluation of the degree of heat checking on 300 cyc of thermal fatigue testing at room temperature to 800 degrees C showed that the die steel containing B was rating 2-3, much better than rating 7 similar to 8 of electroslag remelting ESR-H13 steel for comparison, which mainly because the thermal fatigue cracks were blunted or deflected by boride, and then the cracks spread as scattering shapes was avoided.

Effect of Casting Temperature on the Microstructure and Mechanical Properties of Cu-10Pb-10Sn/42CrMoS4 Bimetallic Hydraulic Cylinder Block

Eff ects of Diff erent Mechanical Alloying Parameters on Microstructure of High Temperature Nanocrystalline Cu-Ta Alloys

EFFECTS OF B ON HIGH TEMPERATURE MECHA-NICAL PROPERTIES AND THERMAL FATIGUE BEHAVIOR OF COPPER DIE-CASTING DIE STEEL

The Effect of the Cu Interlayer on the Interfacial Microstructure and Mechanical Properties of Al/Fe Bimetal by Compound Casting

Effect of Cu Particles on the Properties of Sn-Bi-Pb Low-Melting-Point Alloys

Effects of Thermal Variables of Solidification on the Microstructure and Hardness of the Manganese Bronze Alloy Cu-24Zn-6Al-4Mn-3Fe

Effect of Cooling Rate on the Microstructure and Mechanical Properties of Al-5Cu-0.38Mg-0.32Mn-0.1Ag Alloy Cylinder Heads

Microstructural and mechanical characterization of Al/Cu interface in a bimetallic composite produced by compound casting

Effects of Zn Interlayer on Microstructures and Mechanical Properties of TC4/AZ91D Bimetal via Solid–Liquid Compound Casting Process

Effect of Low Cu Content and Heat Treatment on the Microstructure and Mechanical Properties of High-Vacuum Die-Cast AlSiMgMn Alloys

Effect of Composition and Pouring Temperature of Cu-Sn on Fluidity and Mechanical Properties of Investment Casting

Effect of Sintering Temperature on the Microstructure and Properties of High-Strength and Highly Conductive 5 wt.% ZrB2/Cu Composite

Effect of Cu/Mg-containing intermetallics on the mechanical properties of the as-cast HVDC AlSiMgMnCu alloys by SBFSEM at nano-scale

Effects of Alloying Elements and Temperature on Thermodynamic State and Microstructure of Piston Aluminum Alloy

Interfacial Heat Transfer Behavior at Metal/die in Finger-Plated Casting During High Pressure Die Casting Process

Effects of Heat Treatment on Microstructures and Mechanical Properties of a Low-Alloy Cylinder Liner

Effect of Temperature on Microstructure and Mechanical Properties of Fe-9Ni-2Cu Steel during the Tempering Process

Effect of sintering temperature on the microstructure and properties of Al-7.5Cu-1Si alloy

The Effects of Microstructure on the Thermophysical Properties of the K439B Ni-Based Superalloy

Microstructure evolution and property strengthening of CuCr50 prepared by thermite reduction-electromagnetic casting during the heat treatment process

Enhanced comprehensive performance via alloying and rheo-diecasting in a semi-solid Al–Si–Fe–Mg–Cu–Sr alloy