Abstract:To avoid the "susceptibility artifacts" in magnetic resonance imaging (MRI) and realize patient-specific medical devices with complicated shapes, a novel MRI compatible Zr-1Mo alloy with low porosity (c.a. 0.4%) were manufactured by laser powder bed fusion process(L-PBF) using gas-atomized Zr-1Mo(wt%) alloy powder. However, as-built Zr-1Mo(wt%) components using optimized process parameters show relatively high me-chanical performance(elongation of 6.4%, UTS of 1175 MPa), but contain 0.4 vol% defects which show a spherical morphology and distribute in the builds randomly. These defects definitely deteriorate the mechanical performance(especially ductility, fatigue behavior) of Zr-1Mo components manufactured by L-PBF. In order to eliminate defects in as-built Zr-1Mo components, hot isostatic pressing(HIP), which has been known as an effective process to decrease the porosity of additive manufactured products, was executed. Due to the elevated temperature and high pressure during HIP treatment, the randomly distributed defects were eliminated after the HIP process. Moreover, the alpha-martensite structure in the as-built alloy was transformed into a basketweave alpha + beta structure at low HIP temperature(1023 K and 1073 K) or lamellar alpha + beta structure at relatively high HIP temperature(1173 K and 1273 K). In the meantime, the elongation of HIP-treated Zr-1Mo components significantly increased, but the strength shows the opposite trend. From the viewpoint of mechanical property, Zr1Mo components HIP-treated at 1023 K possessed elongation of 19.9%, and UTS of 628 MPa should be optimized in this study. More importantly, porosity regrowth behavior was investigated to evaluate subsequent heat treatment feasibility for further improvement of mechanical performance. Due to intact raw material power as well as vacuum/low pressure inside the original defect caused by evaporation of metals, porosity regrowth can not be confirmed in HIP-treated Zr-1Mo components after subsequent heat treatment(holding temperature higher than the beta transus of Zr-1Mo alloy). Therefore, further improvement of mechanical performance by subsequent heat treatment for HIP-treated Zr-1Mo components is very promising and should conduct further research in the future

Insight into the interfacial microstructure and chemistry of hot isostatically pressed AA6061-AA6061 bonds for U-10Mo fuel cladding application

Influence of processing on secondary phase formation and microstructural evolution at U-10Mo alloy and Zr interlayer interfaces

Interface characterization of Be/CuCrZr joints by hot isostatic pressing bonding

Evolution of Interface Voids and Columnar Grains of the FeCrAl/RAFMs HIP Bonding Joint

Solid-to-Solid Diffusion Bond Between SA508 Low Alloy Steel to 316L Stainless Steel by Hot Isostatic Pressing

Microstructure and properties of a HIP manufactured SiC p reinforced high alloyed Al–Zn–Mg–Cu–Zr–Ti aluminum matrix composite

Effect of Hot Isostatic Pressing on Microstructure and Mechanical Property of Nial/Cr(Mo,Hf) Composite

The Impact of HIP Process and Heat Treatment on the Mechanical Behaviour of an Al–Si–Mg Alloy Component

Interfacial microstructures, residual stress and mechanical analysis of hot isostatic pressing diffusion bonded joint of 93W–4.9Ni–2.1Fe alloy and 30CrMnSiNi2A steel

Hot Isostatic Pressing for Fatigue Critical Additively Manufactured Ti-6Al-4V

Effects of microstructure characteristics on the tensile properties and fracture toughness of TA15 alloy fabricated by hot isostatic pressing

Microstructure and Mechanical Properties Determined in Compressive Tests of Quasi-Rapidly Solidified NiAl-Cr(Mo)-Hf Eutectic Alloy after Hot Isostatic Pressure and High Temperature Treatments

Near‐Net Shape Hot Isostatic Pressing: Microstructural Analysis and Hardness Evolution at a Steel–Nickel Alloy Interface

The influence of post-thermal treatments on microstructure and mechanical properties in A20X alloy fabricated through powder bed fusion

Combination of Hot Isostatic Pressing and Subsequent Heat Treatment for Additively Manufactured Zr-1Mo Components

Simultaneously improved the strength and ductility of laser powder bed fused Al-Cr-Fe-Ni-V high-entropy alloy by hot isostatic pressing: Microcrack closure and precipitation strengthening

Hot Isostatic Pressing of MRI Compatible Zr-1Mo Components Manufactured by Laser Powder Bed Fusion

Dynamic Research on Ti6Al4V Powder HIP Densification Process Based on Intermittent Experiments

Microstructure, interface and mechanical property of the DS NiAl/Cr(Mo,Hf) composite

Processing of High Interstitial Austenitic Steel with PBF‐LB/M‐Evolution of chemical inhomogeneity and microstructural features during Post‐Processing

Influence of Preheating Temperature on the Microstructure and Mechanical Properties of 6061/TA1 Composite Plates Fabricated by AFSD