Abstract:To optimise the benefits of the deep-rolling process in the service life context of treated components, the process application must be investigated. In addition to the reduction in surface roughness and near-surface material strengthening, compressive residual stresses are introduced, which are primarily responsible for the increase in service life for components, especially in the case of high-strength steel materials. A numerical parameter sensitivity analysis is performed in order to investigate the introduced residual stresses in detail. For this purpose, a validated deep-rolling simulation model is used, which replicates the deep rolling of a railway axle made of the high-strength steel material 34CrNiMo6. The model is based on an elastic-plastic Chaboche material model parameterised on uniaxial tensile and LCF test results and validated with residual stress measurements. Using this model as a basis, the effect of the main process parameters deep-rolling force, feed rate, friction coefficient, number of overruns, tool geometry, and shaft geometry on the resulting residual stress state are investigated. The results reveal that the deep-rolling force has the most significant influence on the introduced residual stress state and should therefore be highlighted. In the case of applying a deep-rolling force of more than 10 kN, maximum compressive residual stresses of around − 1000 MPa are introduced, and a strong saturating behaviour is shown. Maximum compensating tensile residual stresses of + 100 MPa occur below the surface. The main influence of the deep-rolling force is the effective depth achieved, which is determined by the depth of the zero crossing. This varies from 1 mm with an applied force of 2 kN to more than 3.5 mm with 20 kN. Furthermore, the results are analysed to conclude suggestions for the process's applicability, and a proposal for an optimised deep-rolling treatment is presented. There multiple deep rolling with decreased deep-rolling forces is used to achieve a comparably optimised residual stress state. In summary, with the presented results, a contribution to a deeper understanding of the deep-rolling process can be achieved; the influence of the most important process parameters on the residual stress in-depth profiles is established; an optimisation proposal is presented; and correlations are found. Thus, the base work for further fatigue strength assessments and the optimisation of the deep-rolling process regarding the increase of service is laid.

3D numerical modelling of residual stresses induced by reaming

Finite Element Simulation and Analysis of Deformation in Machining of Aeronautical Aluminum Alloy Thin-Walled Workpiece

Influence of the reaming process on hole’s surface integrity and geometry in a martensitic stainless steel 15-5PH

A 3D Analytical Model for Residual Stress in Flank Milling Process

Analytical modeling of milling residual stress under different tool wear conditions

Simulation Study of Cutting-Induced Residual Stress

Thermo-mechanical FE model with memory effect for 304L austenitic stainless steel presenting microstructure gradient

Finite element simulation of residual stress in machining of Ti-6Al-4V with a microstructural consideration

3D Coupled Thermo-Mechanical Simulation of Surface Roughness and Residual Stress in End Milling Aluminum Alloy

A 3D Finite Element Model of Rolling Contact Fatigue for Evolved Material Response and Residual Stress Estimation

Finite element based model for predicting induced residual stresses and cutting forces in AISI 1020 steel alloy

3D Finite Element Simulation and Experiment of Residual Stress on the Cutting Surface

Experimental Study on the Effect of Reaming on the Fatigue Life of Split-Sleeve Cold-Expanded Ti-6Al-4V Alloy Components

Numerical investigation of sequential cuts residual stress considering tool edge radius in machining of AISI 304 stainless steel

Numerical and experimental investigation of tool geometry effect on residual stresses in orthogonal machining of Inconel 718

Fem Analysis and Experimental Study on Residual Stress Induced by Form-Milling and Rolling of Rotor Steel 26Nicrmov145

Effects of Processing Parameters and Tool Geometric Parameters on Residual Stress of Machined 304 Stainless Steel

Prediction of residual stress with multi-physics model for orthogonal cutting Ti-6Al-4V under various tool wear morphologies

Finite element analysis of residual stresses and thin plate distortion after face milling

Predicting Surface Residual Stress for Multi-Axis Milling of Ti-6Al-4V Titanium Alloy in Combined Simulation and Experiments

Numerical parameter sensitivity analysis of residual stresses induced by deep rolling for a 34CrNiMo6 steel railway axle