Abstract:Hole cold expansion is an effective anti-fatigue manufacturing technology, which is widely used in hole strengthening of aviation components. In this paper, a novel small-deep hole (with the diameter less than 2 mm and the depth greater than 10 mm) cold expansion process, called the multi-spherical bump rotating cold expansion process (MBR-CEP), was proposed and verified by experiments on the Inconel 718 superalloy. The MBR-CEP tool with multi-spherical bumps produced by the laser texturing process (LTP) was first designed, and the MBR-CEP with different expansion degrees (δ = 2.1%, 2.6%, and 3.1%) was conducted on small-deep hole specimens. The surface integrity of the small-deep holes before and after the MBR-CEP in the inlet, middle, and outlet areas was studied. Results showed that compared with the small-deep hole after reaming, the hole treated by the MBR-CEP with different δ formed a plastic deformation layer with a maximum depth of 32.73–85.54 μm, a minimum surface roughness of 0.115–0.138 μm in Ra, and a compressive residual stress (CRS) layer with a depth of 0.39–1.077 mm. In addition, the CRS increased by up to 84%, and the microhardness increased by up to 13%. The microstructure evolution on the top surface and sub-surface of the small-deep hole wall was observed by transmission electron microscopy (TEM), which showed that nanocrystals with the size of 48–90 nm and a large number of dislocations and deformation twins formed. Finally, the effectiveness of the proposed process was verified by fatigue tests with different δ at 400 °C. The average fatigue life increased by 3.66 and 8.05 times under δ = 2.1% and 2.6%, respectively. The fatigue fracture surface was examined with scanning electron microscopy (SEM), which revealed that low surface roughness and existence of a plastic deformation layer could effectively reduce the probability of crack initiation.

Experimental Study on the Effect of Reaming on the Fatigue Life of Split-Sleeve Cold-Expanded Ti-6Al-4V Alloy Components

Numerical investigation of the effect of hole reaming on fatigue life by cold expansion

Effect of split-sleeve cold hole expansion on the fatigue performance of an additive manufactured TC18 alloy

Effect of Initial Overload on the Low Cycle Fatigue Life of Gh4169 Alloy at Different Temperatures

A Study of the Back Stress and the Friction Stress Behaviors of Ti-6Al-4V Alloy During Low Cycle Fatigue at Room Temperature

Effect of split sleeve cold expansion on microstructure and fatigue performance of 7075-T6 aluminum alloy holes

Investigation on fatigue performance and microstructure of split sleeve cold expansion of TC4 holes

Numerical Simulation Investigation on Split Sleeve Cold Expansion of Ti-Al Stacked Structure

Study on the Residual Stress Distribution of Bi-Directional Cold Expansion Process Performed on Open Holes

Finite Element Analysis of Split Sleeve Cold Expansion Process on Multiple Hole Aluminum Alloy

Investigation on fatigue failure of split-sleeve cold expansion holes of 7075-T651 aluminum alloy

Simulation Research on Cold Extrusion Strengthening and Reaming of 7050 Aluminum Alloy Plate Hole

Effects of Hole Cold Expansion on Fatigue Behaviors of AlSi10Mg Plate Manufactured by Selective Laser Melting

Cold Hole Expansion Process for Stress Analysis and Evaluation of Fatigue Properties

Factors Influencing Residual Stresses in Cold Expansion and Their Effects on Fatigue Life—A Review

Effect of cold expansion on the fatigue life of multi-hole 7075-T6 aluminum alloy structures under the pre-corrosion condition

Effect of cold expansion on high-temperature low-cycle fatigue performance of the nickel-based superalloy hole structure

Effect of Surface Modification on the High Temperature Low Cycle Fatigue Performance of LPBF 316L Austenitic Steel

Numerical Simulation of Low Cycle Fatigue Behavior of Ti2AlNb Alloy Subcomponents

A novel cold expansion process for improving the surface integrity and fatigue life of small-deep holes in Inconel 718 superalloys

High-temperature fatigue life improvement of small-deep holes by using a novel cold expansion process in a nickel-based superalloy