Abstract:In this study the effect of the cutting speed and an instantaneous heating source directly before cutting tool on the cutting force, cutting zones temperatures chip morphology, shear plane angle and strain rate during dry machining of Ti6Al4V. A 2D numerical model simulating orthogonal cutting process is created using Abaqus/Explicit software. In this model, Johnson Cook constitutive model is used to describe the material behavior during cutting process. Also, Johnson Cook damage model is used to simulation chip separation mechanism. After the verification of the model by comparison with results found in the literature, a number of simulations were run at different levels of four factors: cutting speed (40, 60, 80, 100, 120 and140m/min), heat source temperature (200, 400 and 600°C), heating source distance from the cutting tool (0.3, 0.6 and 0.9mm) and heating source size/diameter (0.6, 0.8 and 1mm). Taguchi L18 orthogonal mixed level design is used to plan for simulation runs using Minitab software. ANOVA analysis is used to investigate the significance of the four factors. The response table of means and the main effect of means is used to compare between the four factors and find their ranking. Based on 95% confidence Interval (CI), the results show that cutting speed has a significant effect on cutting force, strain rate, chip compression ratio, cutting tool nose temperature, cutting tool and chip temperature in the secondary deformation zone, average chip thickness at peaks and average chip thickness at valleys and average pitch. This conclusion is based on the P-values which are << 0.05 and the contribution which reaches 99.01%. Similarly, based on P-values < 0.05 and relatively high contribution reaches 12.16%, the heating source temperature has a significant effect on average chip thickness at valleys, chip compression ratio and strain rate. The cutting speed has Rank 1 among the four factors affecting cutting force, cutting zones temperatures, chip morphology, shear plane angel and stain rate. The effect of instantaneous heating directly before cutting process is negligible compared to the effect of plastic deformation and fracture mechanism in the cutting zone.

Finite element based model for predicting induced residual stresses and cutting forces in AISI 1020 steel alloy

Finite Element Simulation Of High-Speed Cutting Alloy Cast Iron

Simulation of High-Speed Milling Process of Aerospace Aluminum Alloy

Finite element simulation and regression modeling of machining attributes on turning AISI 304 stainless steel

Numerical Simulation Study on Milling Force for Aerospace Aluminum Alloy

Finite Element Simulation and Analysis of Deformation in Machining of Aeronautical Aluminum Alloy Thin-Walled Workpiece

Milling Error Prediction of Thin-Walled Parts During High-Speed Machining

The Role of Material Model in the Finite Element Simulation of High-Speed Machining of Ti6Al4V

Finite element simulation of residual stress in machining of Ti-6Al-4V with a microstructural consideration

A Novel Finite Element Model for Thermally Induced Machining of Ti6Al4V

Finite element simulation of cutting process under the worn tool edge geometries

Prediction of Cutting Forces in Milling Using Machine Learning Algorithms and Finite Element Analysis

Modelling orthogonal cutting of Ti-6Al-4 V titanium alloy using a constitutive model considering the state of stress

Failure mechanics analysis of AISI 4340 steel using finite element modeling of the milling process

Numerical analysis of Johnson-Cook damage model parameters effects on the cutting simulation of AISI 1045

Predictive Modeling and Optimization of Hot Forging Parameters for AISI 1045 Ball Joints Using Taguchi Methodology and Finite Element Analysis

Hybrid modeling with finite element—analysis—neural network for predicting residual stress in orthogonal cutting of H13

Three-dimensional turning force prediction based on hybrid finite element and predictive machining theory considering edge radius and nose radius

Predicting Surface Residual Stress for Multi-Axis Milling of Ti-6Al-4V Titanium Alloy in Combined Simulation and Experiments

Finite element simulations of Ti6Al4V titanium alloy machining to assess material model parameters of the Johnson-Cook constitutive equation

Physics and data driven model for prediction of residual stresses in machining