Abstract:In this study the effect of the cutting speed and an instantaneous heating source directly before cutting tool on the cutting force, cutting zones temperatures chip morphology, shear plane angle and strain rate during dry machining of Ti6Al4V. A 2D numerical model simulating orthogonal cutting process is created using Abaqus/Explicit software. In this model, Johnson Cook constitutive model is used to describe the material behavior during cutting process. Also, Johnson Cook damage model is used to simulation chip separation mechanism. After the verification of the model by comparison with results found in the literature, a number of simulations were run at different levels of four factors: cutting speed (40, 60, 80, 100, 120 and140m/min), heat source temperature (200, 400 and 600°C), heating source distance from the cutting tool (0.3, 0.6 and 0.9mm) and heating source size/diameter (0.6, 0.8 and 1mm). Taguchi L18 orthogonal mixed level design is used to plan for simulation runs using Minitab software. ANOVA analysis is used to investigate the significance of the four factors. The response table of means and the main effect of means is used to compare between the four factors and find their ranking. Based on 95% confidence Interval (CI), the results show that cutting speed has a significant effect on cutting force, strain rate, chip compression ratio, cutting tool nose temperature, cutting tool and chip temperature in the secondary deformation zone, average chip thickness at peaks and average chip thickness at valleys and average pitch. This conclusion is based on the P-values which are << 0.05 and the contribution which reaches 99.01%. Similarly, based on P-values < 0.05 and relatively high contribution reaches 12.16%, the heating source temperature has a significant effect on average chip thickness at valleys, chip compression ratio and strain rate. The cutting speed has Rank 1 among the four factors affecting cutting force, cutting zones temperatures, chip morphology, shear plane angel and stain rate. The effect of instantaneous heating directly before cutting process is negligible compared to the effect of plastic deformation and fracture mechanism in the cutting zone.

Numerical analysis of Johnson-Cook damage model parameters effects on the cutting simulation of AISI 1045

Finite Element Simulation Of High-Speed Cutting Alloy Cast Iron

Numerical Simulation Study on Milling Force for Aerospace Aluminum Alloy

Simulation of High-Speed Milling Process of Aerospace Aluminum Alloy

Parameter identification of Johnson-Cook constitutive model based on genetic algorithm and simulation analysis for 304 stainless steel

Research on Parameter Identification of Johnson–Cook Constitutive Model for TC17 Titanium Alloy Cutting Simulation

The Role of Material Model in the Finite Element Simulation of High-Speed Machining of Ti6Al4V

Parametric Analysis and Improvement of the Johnson-Cook Model for a TC4 Titanium Alloy

Numerical Analysis of Serrated Chip Formation Mechanism with Johnson-Cook Parameters in Micro-Cutting of Ti6Al4V

Evaluation of constitutive models used in orthogonal cutting simulation based on coupled Eulerian–Lagrangian formulation

Investigations on the Johnson-Cook Constitutive and Damage-Fracture Model Parameters of a Q345C Steel

A Novel Finite Element Model for Thermally Induced Machining of Ti6Al4V

A modified parallel-sided shear zone model for determining material constitutive law

Determination and Verification of the Johnson–Cook Constitutive Model Parameters in the Precision Machining of Ti6Al4V Alloy

0610 A Comparative Study on Gao-Zhang and Johnson-Cook Constitutive Models

Optimization of Milling Aluminum Alloy 6061-T6 using Modified Johnson-Cook Model

Research on serrated chip morphology for turning Ti6Al4V titanium alloy by considering damage evolution

A Modified Johnson–Cook Constitutive Model and Its Application to High Speed Machining of 7050-T7451 Aluminum Alloy

Research on inverse identification of Johnson-Cook constitutive parameters for turning 304 stainless steel based on coupling simulation

Coupled Thermo-mechanical Model for Metal Orthogonal Cutting Process and Finite Element Simulation

Finite element simulations of Ti6Al4V titanium alloy machining to assess material model parameters of the Johnson-Cook constitutive equation