Abstract:The isotopic composition of sulfur is a vital tracer used in the Earth and planetary sciences. In this study, the laser- and ICP-induced isotopic fractionation in S-rich minerals (sulfides and elemental S) with different matrices was investigated by using 257 nm femtosecond (fs) and 193 nm ArF excimer nanosecond (ns) laser ablation systems coupled to a Neptune Plus MC-ICP-MS. Compared to ns-LA-MC-ICP-MS, higher sensitivity (1.4–2.4 times) under similar instrumental conditions and better precision (∼1.6-fold) under the same signal intensity condition were achieved by fs-LA-MC-ICP-MS. In addition, a fs-laser provides less fluence and matrix dependent S isotopic fractionation, and more stable transient isotopic ratios compared to a ns-laser. Better results acquired by fs-LA-MC-ICP-MS were attributed to the smaller size of particles and less thermal effect produced by using the fs-laser, which were evidenced by the morphologies of the ablation craters and ejected aerosol particles of P-S-1 (the pressed powder pellet of IAEA-S-1) and PPP-1 (a pyrite single crystal from the Sukhoi Log deposit). The ICP-induced isotopic fractionation (matrix effect) was still found in fs-LA-MC-ICP-MS under the maximum sensitivity conditions. However, a significant reduction of the matrix effect was obtained under robust plasma conditions at a lower makeup gas flow rate (0.52–0.54 l min−1) relative to the maximum sensitivity condition (0.6 l min−1) for S isotope analysis. This could be ascribed to the particles that not only pass into the higher temperature ICP for a longer residence time at a lower makeup gas flow rate that resulted in more efficient vaporization of the particles, but also experience a more robust plasma induced by adding 4–6 ml min−1 N2 into the plasma. Furthermore, under the robust conditions, the results of six reference materials with different matrices obtained by fs-LA-MC-ICP-MS with non-matrix matched calibration with a spot size of 20–44 μm showed excellent agreement with the reference values (the accuracy of 0.01–0.15‰ for δ34S and 0.11–0.45‰ for δ33S and the precision of 0.16–0.40‰ (2 s) for δ34S and 0.35–0.78‰ (2 s) for δ33S) and the mass-dependent fractionation line, validating the applicability of the proposed approach for providing high-quality in situ isotope data (δ33S and δ34S) of sulfides and elemental sulfur at high spatial resolution using non-matrix matched analysis.

Development of a Matrix‐Matched Barite Reference Material (NWU‐Brt) for Calibration of In Situ S Isotope Measurements by Laser Ablation Multi‐Collector Inductively Coupled Plasma‐Mass Spectrometry

Preparation of Sulfur-Bearing Reference Materials for in Situ Sulfur Isotope Measurements Using Laser Ablation Multicollector Inductively Coupled Plasma–mass Spectrometry

In-Situ Sulfur Isotopic Analysis of Sulfate by Laser Ablation Multiple Collector Inductively Coupled Plasma Mass Spectrometry (LA-MC-ICP-MS)

Three new potential sulfur reference materials (pyrite, gypsum, and arsenopyrite) for in situ sulfur isotope analysis by laser ablation MC-ICP-MS

New Potential Sphalerite, Chalcopyrite, Galena and Pyrite Reference Materials for Sulfur Isotope Determination by Laser Ablation‐MC‐ICP‐MS

Barite, Anhydrite and Gypsum Reference Materials for in Situ Oxygen and Sulfur Isotope Ratio Measurements

New Potential Sphalerite, Chalcopyrite, Galena and Pyrite Reference Materials for Sulfur Isotope LA-MC-ICP-MS Determination

Determining 88sr/86sr of Barite Using the Na2CO3 Exchange Method

Determining Ba Isotopes of Barite Using the Na2CO3 Exchange Reaction and Double-Spike Method by MC-ICP-MS

Barite oxygen isotope reference materials for highly precise and accurate SIMS microanalysis

A Synthesized Sphalerite Standard for in Situ Analysis of Sulfur Isotopes and Trace Elements by LA-MC-ICP-MS and LA-ICP-MS

Development of two novel natural calcite reference materials for enhanced in situ elemental and Sr isotopic analysis.

A Quantity Chalcopyrite Reference Material for in Situ Sulfur Isotope Analysis

High‐Precision Barium Isotope Measurements of Carbonates by MC‐ICP‐MS

Accurate Determination of Ba Isotope Ratios in Barite Samples by LA-MC-ICP-MS

High-precision barium isotope measurements by MC-ICP-MS

Synthesis of molybdenite reference materials for in situ molybdenum and sulfur isotope measurement using laser ablation MC-ICP-MS

Calcite TLM and LSJ07-two Natural Low-Sr Reference Materials for Microbeam Sr Isotope Analysis

A potential stibnite reference material for sulfur isotope determination by LA-MC-ICP-MS

Accurate determination of sulfur isotopes (δ33S and δ34S) in sulfides and elemental sulfur by femtosecond laser ablation MC-ICP-MS with non-matrix matched calibration