Abstract:A novel Al-Cu-Ni composite, featuring Ni-Al 3 Ni 2 /Al 3 Ni core–shell intermetallics within its matrix produced via powder metallurgy, was subjected to isothermal compression tests at different conditions so as to garner an insight into its hot deformation behaviour. These experiments were conducted from 300 to 500 °C, with strain rates varying from 0.0001 s −1 to 0.1 s −1 . It is found that the flow stress is influenced by both strain rate and temperature. As the deformation temperature reduced or the strain rates increased, the peak stress level increased. To characterize the flow stress of the composite, a sine-hyperbolic constitutive equation was developed and the calculated value of activation energy (234 kJ/mol) was substantially higher than that for the self-diffusion of pure Al. Subsequently, the strain-compensated Arrhenius model and the artificial neural network (ANN) model were developed to predict the composite flow behaviour. With a lower average absolute relative error of 2.266%, a smaller root means square error of 0.668 MPa, and a higher correlation coefficient of 0.999 than the Strain-compensated Arrhenius model, the ANN model is more predictable. The processing maps show that the ideal hot working conditions for the composite are between 400 and 500 °C, with strain rates between 0.0001 s −1 and 0.01 s −1 with an efficiency of 37%. The uneven distribution in the shape and size of Core–shell/Al 3 Ni intermetallic compounds influenced the flow stress curves, leading to dynamic recrystallization (DRX), followed by partial dynamic recovery (DRV), and ultimately strain hardening at 0.01 s −1 & 0.1 s −1 . The occurrence of recrystallization and recovery up to a specific strain followed by strain hardening at all the deformation temperatures is a rare phenomenon and has been attributed to the structure and composition of core–shell intermetallics. The occurrence of work hardening at higher strains throughout the operational range of temperatures imparts greater reliability to structural components.

A phenomenological constitutive model of Novel Rheo Gravity Die Cast Al-15Mg 2 Si-4.5Si-0.01Sr-0.015B composite

Effect of Fluid Flow on Microstructure Evolution During Rheo Gravity Die Casting of Novel Al–15Mg2Si–4.5Si Composite

Constitutive Modeling of High-Temperature Flow Behavior of Al-0.62Mg-0.73Si Aluminum Alloy

An innovative constitutive material model for predicting high temperature flow behaviour of inconel 625 alloy

Dislocation Density-Based Model for Flow Behavior of a Near-α Titanium Alloy Considering Effects of Initial Lamellar Thickness

Studies on Hot Deformation Behavior and Dynamic Recrystallization in a High Al Ferritic Low-Density Steel

A Comparative Study on Modified Johnson–Cook and Arrhenius-Type Constitutive Models to Predict the Hot Deformation Behaviour of Molybdenum-Hafnium-Carbide Alloy

Phenomenological Constitutive Model and Physical Constitutive Model of Hot Deformed Dual-Phase Ti-5Al-4Sn-2Zr-5Mo Alloy

Comparative Study on Several Constitutive Models of GCr15 Steel at High Strain Rates

Constitutive analysis of hot deformation behavior of a Ti6Al4V alloy using physical based model

A Modified Johnson–Cook Model and Microstructure Evolution of As-Extruded AA 2055 Alloy during Isothermal Compression

Modelling the Flow Behaviour of Al Alloy Sheets at Elevated Temperatures Using a Modified Zerilli-Armstrong Model and Phenomenological-Based Constitutive Models

Microstructure Characteristics and Comparative Analysis of Constitutive Models for Flow Stress Prediction of Inconel 718 Alloy

Experimental Investigations and Constitutive Modeling of the Dynamic Recrystallization Behavior of a Novel GH4720Li Superalloys with Yttrium Micro-Alloying

High strain rate compression deformation mechanism and constitutive equation of fine grained Mg–7Gd–5Y–1.2Nd–0.5Zr alloy at different temperatures

Constitutive behavior of as-cast A356

A modified Johnson-Cook model considering strain softening of A356 alloy

Influence of core–shell intermetallic on dynamic recrystallization and processing maps of novel Al-Cu-Ni composite through Arrhenius and artificial neural network (ANN) models

Characteristics of work hardening and constitutive models comparison of powder metallurgy Al-5.6Zn-2Mg alloy during hot compression

On the Constitutive Models for Ultra-High Strain Rate Deformation of Metals

Constitutive Descriptions and Restoration Mechanisms of a Fe-17Cr Alloy during Deformation at Temperatures of 700–1000 °C