Abstract:In machining, heat concentration is generated at the surface contact between the tool and workpiece. This is the effect of hard frictions at the shear cutting plane to remove hard and brittle materials. The highly adhesive behavior of aluminum alloy 6061-T6 is more severe in higher cutting temperature, which may affect tool failures such as flank wear, tool chip and built-up edge, particularly on the edge of cutting inserts during the process. As a result, this may lead to the rough surface and low-dimensional accuracy of the machined parts. Realizing that metal-cutting industry players are demanding high-quality products with better surface finish and dimensional accuracy led to this study. Aluminum alloy 6061-T6 is a standard alloy used in automotive, aerospace and food packaging due to good hardness, high strength-to-weight ratio, resistance to corrosion and weldability. In order to address this problem, a newly developed metal working fluid which is SiO2-Al2O3-ZrO2 tri-hybrid nanofluid is applied in the cutting zone to achieve a good surface finish of the machined parts and lowering the cutting temperature. This study is the first attempt to enhance machining performance, particularly at high-speed machining, by employing a combination of tri-hybrid nanofluids and a minimum quantity lubricant technique. Industrial standards include uncoated tungsten carbide and CVD TiCN-Al2O3 carbide used during machining of aluminum alloy 6061-T6. The minimum quantity lubricant method is an alternative in supplying the lubricant into the machining zone due to flood machining and conventional fluid possess safety, health, economic and environmental effects. In this study, the experimental data were analyzed statistically using analysis of variance and response surface methodology. The responses studied were reduced significantly when tri-hybrid nanoparticles present at the cutting interface with higher MQL flow rate and concentration. There are two-factor interactions which are significant to the responses studied. Therefore, the combinations of MQL and excellent tri-hybrid nanofluids characteristics have enhanced between 16 and 76% of surface roughness and the cutting temperature, respectively, which is very promising in the future.

Exploring cutting parameters for enhanced performance in abrasive water jet machining of Al 6061 hybrid nanocomposite

Characterization and Optimization of Abrasive Water Jet Machining Parameters of aluminium/silicon carbide Composites

Experimental Investigation and Molecular Dynamics Simulation of Contributing Variables on Abrasive Water Jet on Aluminum Alloy 7075 Reinforced with Al2O3, Graphite and Silicon Carbide

Analysis and Optimization of Abrasive water Jet Machiningprocesses on the hybrid nano particle reinforced Aluminum alloy matrix composite material

Effect of ceramic particle reinforcement type and process parameters on abrasive water jet processing of aluminum metal matrix composites fabricated by stir casting and hot rolling

Optimization of Abrasive Water Jet Machining of SiC Reinforced Aluminum Alloy Based Metal Matrix Composites Using Taguchi–DEAR Technique

Exploring tribological properties in the design and manufacturing of metal matrix composites: an investigation into the AL6061-SiC-fly ASH alloy fabricated via stir casting process

Effect of silicon carbide on kerf convergence and irregularity of the surface during abrasive water jet machining of fiber-metal hybrid composites

Characterization and Defect Analysis of Machined Regions in Al-SiC Metal Matrix Composites Using an Abrasive Water Jet Machining Process

Machining Efficiency and Property Change Analysis of Ti-6Al-4V Alloy Processed by Abrasive Water Jet Machining

Experimental investigation to assess the surface integrity in WEDM of Al-based hybrid composite material

Abrasive waterjet machining of titanium alloy using an integrated approach of taguchi-based passing vehicle search algorithm

Advanced Material Processing: Optimization of Abrasive Water Jet Parameters for Metal-Stacked Hybrid Fiber Laminate

Investigation of Abrasive water jet machining parameters of Bismaleimide composites

Experimental investigation on surface characteristics of Ti6Al4V alloy during abrasive water jet machining process

Effect of reinforced particles on the machinability of Al alloy under MQL, cryogenic, and hybrid lubrication

Machining of aluminium nitride ceramic using developed hot abrasive jet machining: an experimental and simulation approach

Effects of SiO2-Al2O3-ZrO2 Tri-hybrid Nanofluids on Surface Roughness and Cutting Temperature in End Milling Process of Aluminum Alloy 6061-T6 Using Uncoated and Coated Cutting Inserts with Minimal Quantity Lubricant Method

An experimental assessment and optimisation of hole quality in Al2024-T3 aluminium alloy during abrasive water jet machining

An Experimental Investigation on Machining of Hardened AISI 440C Stainless Steel Using Abrasive Water Jet Machining Process

Parametric optimisation of milling process for the machining of carbon nanotubes-based hybrid aluminium composite