Abstract:Abstract Owing to its outstanding properties such as corrosion resistance, low density, relatively low cost, and stiffness, Al2024-T3 aluminium alloy has been widely applied in aircraft manufacturing. To perfectly assemble an aircraft, numerous high-quality holes are drilled into its structures employing conventional drilling processes. Conventional drilling poses some challenges such as thermal distortions, burr formations, and tool wear. Alternatively, abrasive water jet drilling (AWJD) is a thermal-free machining process that can be employed as an alternative to conventional drilling of aeronautical structures. Hence, in this work, the effect of abrasive water jet parameters, namely stand-off distance, water jet pressure, and abrasive mass flow rate, on hole-quality parameters was evaluated at traverse speed = 10 mm/min. Three parameters were stand-off distance = 1, 2, and 3 mm, abrasive mass flow rate = 200, 250, and 300 g/min, and water jet pressure = 1800, 2100, and 2600 bar. Using a 6 mm circular-movement diameter of the nozzle tip, optimal stand-off distance, water jet pressure, and abrasive mass flow rate obtained by multi-objective optimization were 2 mm, 250 g/min, and 2600 bar, respectively. The corresponding hole-quality parameters were Diameter = 6.232 mm, Kerf angle = 0.018°, Cylindricity = 0.051 mm, Perpendicularity = 0.033 mm, Circularity = 0.0041 mm and Surface roughness R a = 2.909 μm. The results showed that water jet pressure had the greatest influence on Perpendicularity, Circularity; stand-off distance had the highest effect on Kerf angle; and abrasive mass flow rate has the largest influence on Hole diameter, Cylindricity and Surface roughness R a , and R z at the given value of traverse speed. The adopted optimization process for abrasive water jet of Al2024-T3 aluminium alloy was successfully verified through confirmation runs, clearly illustrating its benefits.

Machining of aluminium nitride ceramic using developed hot abrasive jet machining: an experimental and simulation approach

Comparative performance investigation and sustainability evaluation between hot-AJM and AJM during machining of zirconia ceramic using Al2O3 abrasives

Experimental Investigation of Aluminum Nitride Ceramics Based on Compliant Finishing Process

Aluminium Nitride Surface Characterization by Grinding with Laser-Ultrasonic Coupling

Characterization and Optimization of Abrasive Water Jet Machining Parameters of aluminium/silicon carbide Composites

Analysis and Optimization of Abrasive water Jet Machiningprocesses on the hybrid nano particle reinforced Aluminum alloy matrix composite material

Parametric optimisation of milling process for the machining of carbon nanotubes-based hybrid aluminium composite

Optimization of Abrasive Water Jet Machining of SiC Reinforced Aluminum Alloy Based Metal Matrix Composites Using Taguchi–DEAR Technique

Effect of Nanoaluminium Nitride Ceramic Particles on Microstructure, Mechanical Wear, and Machining Behavior of Al-Si-Mg Alloy Matrix Composites Produced by Bottom Pouring Type Stir Casting Route

Experimental investigation on the effet of input paramètres on surface roughness and MRR of abrasive flow machining process

Experimental investigation to assess the surface integrity in WEDM of Al-based hybrid composite material

An experimental assessment and optimisation of hole quality in Al2024-T3 aluminium alloy during abrasive water jet machining

Computer aided simulation and experimental investigation of the machinability of Al 6065 T6 during milling operation

Material response to particle impact during abrasive jet machining of alumina ceramics

Machining Efficiency and Property Change Analysis of Ti-6Al-4V Alloy Processed by Abrasive Water Jet Machining

Synthesis of AA8050/B4C/TiB2 Hybrid Nanocomposites and Evaluation of Computer-Aided Machining Parameters

Comparative evaluation and sensitivity analysis of multi-modelling and optimization of milling Ti–6Al–4V alloy with high-pressure coolant jets

Experimental investigations with machine learning techniques for understanding of erosion wear in advanced aluminum nanocomposites

Machine learning approach for prediction analysis of aluminium alloy on the surface roughness using CO2 laser machining

Machine learning based modelling and optimization in hard turning of AISI D6 steel with newly developed AlTiSiN coated carbide tool

A Numerical Simulation of Machining 6061 Syntactic Foams Reinforced with Hollow Al2O3 Shells