Abstract:The traditional way to machine hybrid composites is hard because they tend to break, have a high retraction, have a high service temperature, and have an uneven surface irregularity. For high-strength fiber/metal composite constructions, alternative machining methods have drawn interest as a solution to these problems. Current research focuses on enhancing the Abrasive Water Jet Machining process by optimizing its variables using a composite material of epoxy reinforced with silicon carbide, stainless steel wire mesh, and Kevlar. The variables assessed are the Nozzle-to-substrate gap (S), the Abrasive discharge molding and different percentages of silicon carbide (SiC) filler (0%, 3%, and 6% by weight), three different types of hybrid laminates (H1, H2, and H3) were produced. The response surface method (RSM) was utilized in this learning, specifically on a central composite design, to calculate and optimize machining variables based on the Kerf convergence ratio (Kt) and Surface irregularity (Ra) as responses. According to the results, the traverse feed velocity, Abrasive discharge proportion, and Nozzle-to-substrate gap are the critical factors in determining Surface irregularity and Kerf convergence width (H1 laminate) for a fiber/metal laminate with 0%, 3% and 6% weight fraction. In the case of a 3% weight fraction H2 laminate, the traverse feed velocity was identified as the primary factor affecting the Kerf convergence ratio. In contrast, traverse feed velocity and Nozzle-to-substrate gap had the most significant influence on Surface irregularity. The findings also indicated that S, followed by Abrasive discharge proportion and traverse feed velocity, are the variables that have the most significant influence when cutting 6 wt% SiC filler particle fiber/metal laminate (H3 laminate). For Surface irregularity, the combination of traverse feed velocity and Nozzle-to-substrate gap had the most significant impact. To validate the optimization results, confirmatory tests was conducted, and the findings were very similar to the experimental values, indicating the accuracy and effectiveness of the optimization process. To better understand the manufacturing processes, a scanning electron microscope was used to examine the morphological features of the machined surfaces, such as delamination, fibre breakage, and fibre pull-out.

Experimental Investigation and Molecular Dynamics Simulation of Contributing Variables on Abrasive Water Jet on Aluminum Alloy 7075 Reinforced with Al2O3, Graphite and Silicon Carbide

Characterization and Optimization of Abrasive Water Jet Machining Parameters of aluminium/silicon carbide Composites

Optimization of Abrasive Water Jet Machining of SiC Reinforced Aluminum Alloy Based Metal Matrix Composites Using Taguchi–DEAR Technique

Effect of silicon carbide on kerf convergence and irregularity of the surface during abrasive water jet machining of fiber-metal hybrid composites

Effect of ceramic particle reinforcement type and process parameters on abrasive water jet processing of aluminum metal matrix composites fabricated by stir casting and hot rolling

A Statistical and Optimization Study on the Influence of Different Abrasive Types on Kerf Quality and Productivity during Abrasive Waterjet (AWJ) Milling of Ti-4Al-6V

An Experimental Investigation on Machining of Hardened AISI 440C Stainless Steel Using Abrasive Water Jet Machining Process

Advanced Material Processing: Optimization of Abrasive Water Jet Parameters for Metal-Stacked Hybrid Fiber Laminate

Characterization and Defect Analysis of Machined Regions in Al-SiC Metal Matrix Composites Using an Abrasive Water Jet Machining Process

Effect of Abrasive Water Jet Parameters on the Drilling of Aluminum Foam Sandwiched with Glass Fiber Polymer Composites

Experimental study of delamination and kerf geometry of carbon epoxy composite machined by abrasive water jet

An experimental assessment and optimisation of hole quality in Al2024-T3 aluminium alloy during abrasive water jet machining

Experimental and simulation study on the influence factors of abrasive water jet machining ductile materials

Experimental study, modeling, and parametric optimization on abrasive waterjet drilling of YSZ-coated Inconel 718 superalloy

Machining Efficiency and Property Change Analysis of Ti-6Al-4V Alloy Processed by Abrasive Water Jet Machining

Investigation of Abrasive water jet machining parameters of Bismaleimide composites

Simultaneous optimization of process parameters during abrasive water jet machining on glass fibre reinforced polymer

Experimental investigation on the effet of input paramètres on surface roughness and MRR of abrasive flow machining process

Enhancing High-Alloy Steel Cutting with Abrasive Water Injection Jet (AWIJ) Technology: An Approach Using the Response Surface Methodology (RSM)

Statistical modelling of depth milling in Ti-6AL4V using abrasive water jet machining

Influence of Ceramic Particles Additives on the Mechanical Properties and Machinability of Carbon Fiber/Polymer Composites