Abstract:OBJECTIVE:To evaluate the colouration of zirconia ceramic by adding three kinds of rare earth oxides. The influence of the pigments concentration on the mechanical properties and the microstructure was also analyzed.METHODS:Added different concentrations of CeO(2), Er(2)O(3) and Pr(6)O(11) in tetragonal zirconia poly crystals stabilized with 3 mol% yttria (3Y-T2P) powder, compacted at 200 MPa using cold isostatic pressure, and sintered to 1 400 degrees C. The heating rate was 150 degrees C/h and the dwelling time was 2 hours. The chromaticity of sintered bodies was measured with chroma meter. The relative density, hardness, flexure strength and fracture toughness were investigated as well. The phase stability of the colorized and pure zirconia was evaluated by X-ray diffraction (XRD) using an automated diffractometer. The microstructures of the specimens were evaluated by scanning electron microscope (SEM).RESULTS:Several kinds of color achieved by the different pigments praseodym oxide, cerium oxide and erbium oxide were presented in the CIELab system. The a* value increased with the added amount of Er(2)O(3), while b* value rose with the increasing amount of CeO(2) and Pr(6)O(11). However, three pigments failed to decrease L* value and the sintered body appeared too bright. Adding three pigments influenced flexure strength of zirconia ceramic significantly, but had little influence on the hardness and fracture toughness. Microscopy revealed the relationship between the porosity and shapes of grains was correlated to strength of the diphase ceramics. No additional phase could be detected by XRD, except t-ZrO(2) in all colorized samples after sintering at 1 400 degrees C for 120 min.CONCLUSIONS:Zirconia ceramic can be colorized by CeO(2), Er(2)O(3), and Pr(6)O(11). Pigments even in a small amount influence the mechanical properties of the colorized zirconia material, which necessitates further investigation.

Preparation, characterization and coloring mechanism of 3D printed colorful ZrO 2 ceramics parts

[Effect of Three Kinds of Rare Earth Oxides on Chromaticity and Mechanical Properties of Zirconia Ceramic].

Preparation and stereolithography 3D printing of ultralight and ultrastrong ZrOC porous ceramics

Fabrication of Coloured Zirconia Ceramics by Infiltrating Water Debound Injection Moulded Green Body

Preparation and property characterization of Zr-modified Si-O-C-based precursor ceramics through three-dimensional printing

Properties and ceramic transformation of Si–Zr–O–C precursor ceramics with porous structure

Fabrication of Blue-Colored Zirconia Ceramics via Heterogeneous Nucleation Method

Fabrication of High-Performance Al2O3-ZrO2 Composite by a Novel Approach That Integrates Stereolithography-Based 3D Printing and Liquid Precursor Infiltration

Fabrication of black-colored CuO–Al2O3–ZrO2 ceramics via heterogeneous nucleation method

Preparation of excellent performance ZTA ceramics and complex shaped components using digital light processing 3D printing technology

The Color of Fe<sub>2</sub>O<sub>3</sub> and Bi<sub>2</sub>O<sub>3</sub> Pigmented Dental Zirconia Ceramic

Pigments based on Er2O3-Al2O3: Preparation and colouring performance in zirconia ceramics

Digital Light Processing of Rare Earth Oxide Doped Natural Color Zirconia Denture for Customized Aesthetic Properties

The preparation of ZrO2-Al2O3 composite ceramic by SLA-3D printing and sintering processing

Debinding behaviour and sintering temperature-dependent features of coloured zirconia fabricated by ceramic injection moulding

Additively Manufactured Zirconia for Dental Applications with In Situ Color Gradation Control

Effect of Pigmentation on the Mechanical Properties and Microstructure of Dental 3Y-TZP Ceramics

Fused deposition fabrication of high-quality zirconia ceramics using granular feedstock

Color Reproduction And Shade Stability Of Zirconia Ceramics

A Comprehensive Study on Zirconia Slurry for Stereolithography-Based Additive Manufacturing

Effects of added aluminum chromium slag on the structure and mechanical properties of colored zirconia ceramics