Abstract:Poly(lactide-co-glycolide) (PLGA) copolymers are the most prevalent materials for tissue engineering applications. To mimic the real microenvironment of extracellular matrix (ECM) for cell growth, nanofibrous PLGA scaffolds are preferred. PLGA5050 (in which the molar ratio of lactidyl to glycolidyl units is 50:50), which is an utterly amorphous polymer, was first reported to be made into nanofibrous networks (fiber diameter around 500nm) using phase separation from PLGA5050/THF solutions in this study. The concentration of polymeric solution had significant effects on fiber diameter and unit length. Nonsolvent (e.g. H2O) was unnecessary to form the PLGA5050 gel, which was critical to nanofibrosis, as if the environmental temperature for gelation occurrence was low enough (−70°C). The physical crosslinks to stabilize the PLGA5050/THF gel were believed to be GA segments along the backbone owing to their inferior solubility in THF. The addition of H2O would cause adverse effects of liquid–liquid phase separation and nanofibrosis failure owing to the hydrophilicity of glycolidyl units. Associating with the phase separation method, particle-leaching technique was applied to fabricate three-dimensional scaffolds with macroporous and nanofibrous structures. To ensure the occurrence of nanofibrosis on macropore walls, the temperature of salt particles should be best lowed to −70°C beforehand. Accordingly, scaffolds prepared under varied parameters exhibited different nanofiber and pore morphologies, which affected the pore size, porosity, specific surface area, water contact angle and protein adsorption ability etc. The preliminary cell (MC3T3-E1) culture confirmed the cell ingrowth into the macroporous and nanofibrous PLGA5050 scaffolds in comparison with the solely nanofibrous matrixes. This kind of bi-scaled three dimensional matrixes can be superior candidate scaffolds for tissue engineering applications.

Control of pore size and structure of tissue engineering scaffolds produced by supercritical fluid processing.

Fabrication Of Pcl Scaffolds By Supercritical Co2 Foaming Based On The Combined Effects Of Rheological And Crystallization Properties

Processing and Characterization of Supercritical CO2 Batch Foamed Poly(lactic Acid)/poly(ethylene Glycol) Scaffold for Tissue Engineering Application

Preparation of PLGA/β-TCP Composite Scaffolds with Supercritical CO2 Foaming Technique

Novel Fabricating Process for Porous Polyglycolic Acid Scaffolds by Melt-Foaming Using Supercritical Carbon Dioxide

Polymerization of D,L-Lactide and in Situ Fabrication of PDLLA Porous Scaffolds in Supercritical Carbon Dioxide

A Novel Route to the Generation of Porous Scaffold Based on the Phase Morphology Control of Co-Continuous Poly(ε-Caprolactone)/polylactide Blend in Supercritical CO 2

Preparation of Open-Porous Stereocomplex PLA/PBAT Scaffolds and Correlation Between Their Morphology, Mechanical Behavior, and Cell Compatibility.

Facile Preparation of Open-Cellular Porous Poly (L-Lactic Acid) Scaffold by Supercritical Carbon Dioxide Foaming. for Potential Tissue Engineering Applications

Synthesis of CS-g-PDLLA Copolymer and In-Situ Fabrication of CS-g-PDLLA/PDLLA Porous Scaffolds in Supercritical Carbon Dioxide

Specially Elaborated Thermally Induced Phase Separation to Fabricate Poly(L-Lactic Acid) Scaffolds with Ultra Large Pores and Good Interconnectivity

Multi-modal cell structure formation of poly (lactic-co-glycolic acid)/superparamagnetic iron oxide nanoparticles composite scaffolds by supercritical CO<sub>2</sub> varying-temperature foaming

Mechanical and Thermal Property Characterization of Poly- L -Lactide (PLLA) Scaffold Developed Using Pressure-Controllable Green Foaming Technology

Preparation of Highly Porous Interconnected Poly(Lactic Acid) Scaffolds Based on A Novel Dynamic Elongational Flow Procedure

Macroporous and nanofibrous poly(lactide-co-glycolide)(50/50) scaffolds via phase separation combined with particle-leaching

Preparation of magnetic scaffolds via supercritical carbon dioxide foaming process using iron oxide nanoparticles coated with CO2‐philic materials as nucleating agents

Controllable fabrication of multi-modal porous PLGA scaffolds with different sizes of SPIONs using supercritical CO2 foaming

Controllable fabrication of multi‐modal porous <scp>PLGA</scp> scaffolds with different sizes of <scp>SPIONs</scp> using supercritical <scp> CO <sub>2</sub> </scp> foaming

Design and synthesis of novel polycaprolactone-chitosan based scaffolds using supercritical carbon dioxide

Fabrication of Super-Hydrophilic and Highly Open-Porous Poly (lactic Acid) Scaffolds Using Supercritical Carbon Dioxide Foaming.

Preparation of porous PLA scaffold materials by supercritical CO2 fluid technique