Abstract:Zirconium alloys have been used as primary materials for fuel cladding which protect the nuclear fuel from the outside in the nuclear power system. Zirconium alloys have very low absorption cross-section of thermal neutrons, high hardness, ductility, and corrosion resistance [1]. However, they had problems with nuclear reactor safety as they reacted violently with steam at high temperature, producing large amounts of hydrogen and heat, and having low mechanical strength at high temperature. Moreover, a massive hydrogen explosion by zirconium-steam interaction occurred at the Fukushima Daiichi nuclear power plant. The development of accident-tolerant fuel cladding has been widely studied since the Fukushima nuclear reactor accident [2]. Ideas and new concepts have been proposed for accident-tolerant fuel cladding to prevent hydrogen explosion by inhibiting reaction with steam in the accident environment. Therefore, the ATF research was actively carried out in the early development period to replace zirconium alloys using materials such as SiC, FeCrAl, etc., which have oxidation resistance better than zirconium [3,4]. However, the phenomenon of dissolution in cooling water under normal operating conditions was observed, and some materials had lower economic feasibility because the neutron absorption cross-section area was larger than zirconium. To overcome these problems, many researches are underway to take both stability and economy by coating the surface of zirconium cladding. By applying coating technology to zirconium cladding, it is easy to obtain corrosion resistance without a change in the base materials. Recently, Terrani et al. reported the oxidation resistance of Fe-based alloys for protecting zirconium alloys from the rapid oxidation in a high-temperature steam environment. Kim and co-workers also reported the corrosion behavior of Cr-coated zirconium alloy using a plasma spray and laser beam scanning [5]. In the present work, Cr anti-oxidation coating was fabricated on a commercial Zircaloy-4 cladding using cathodic arc ion plating (CAIP) because cathodic arc ion plated films tend be denser and have better adhesion characteristics than films produced using other method [6]. The Cr system was selected because of its good corrosion resistance. The microstructures of arc ion plated Cr coating were characterized. The oxidation behavior of the coating was analyzed. . 2. Experimental CAIP is well recognized method of producing protective coatings due to its high ionization efficiency and excellent film adhesion. It is a promising method for depositing oxidation-resistant coatings on nuclear fuel claddings. Pure Cr coating was deposited on the Zircaloy-4 using the CAIP with Cr target (99.59% purity). Figure. 1 shows the CAIP system which was designed to coat protective film onto the surface of a nuclear cladding. The substrates were cleaned ultrasonically in acetone and an ethanol solution, and the substrates were then mounted in a vacuum chamber. The chamber was evacuated to a pressure of 1 x 10 Torr, and heated simultaneously to 1473 K to remove the residual gas adsorbed on the chamber wall and substrates. Prior to the deposition, the substrates were sputter cleaned using Ar ions under -400V negative bias voltage for 5 min. Cr ion bombardment was applied to remove contaminants and ensure good adhesion of deposited coatings. The deposition of Cr was carried out in an Ar atmosphere with a pressure of 20mTorr. In order to study the effects of negative bias voltage, different negative bias voltages ranging from -25 to -100V were applied. After deposition, the coatings were polished to reduce the influence of the roughness, as well as for more precise measurements.

Microstructure and flow accelerated corrosion resistance of Cr coatings electrodeposited in a trivalent chromium bath

Corrosion Properties of Cr Coating Deposited on Nuclear Fuel Cladding

Preparation of Al-Cr-Fe Coatings by Heat Treatment of Electrodeposited Cr/Al Composite Coatings

Autoclave grid-to-rod fretting corrosion behaviors of the Zr alloy fuel cladding with and without Cr coating through advanced characterization

Microstructure and corrosion behavior of Cr and Cr–P alloy coatings electrodeposited from a Cr(III) deep eutectic solvent

Microstructure Evolution and Failure Mechanism of Cr-coated Zry-4 in Air and Steam at 1200 °C

Microstructure and electronic structure of Cr2C and Fe2Y in the Cr-coating prepared by pack-cementation on the surface of ODS steel

Mechanical and high-temperature steam oxidation properties of Cr coatings deposited via high-power impulse magnetron sputtering

Investigations on 1200 °C steam oxidation behavior of Cr coatings with distinct crystallographic orientation on Zircaloy-4 alloys

Direct and Pulse Electroplating Effects on the Diffusion Barrier Property of Plasma-Nitrided Cr Coatings on HT9 Steel

Insights into 1200 °C steam oxidation behavior of Cr coatings with different microstructure on Zircaloy-4 alloys for enhanced accident tolerant fuel cladding

Corrosion resistance of 316 stainless steel in a simulated pressurized water reactor improved by laser cladding with chromium

Mitigating fuel cladding chemical interactions by enhancing chromium diffusion barrier performance using pulse reverse electroplating

Effect of buffer layer on oxidation and corrosion resistance of CrN coatings on Zr alloy prepared by FCVAD technology

In-situ study on the microstructure and cracking behavior of annealed Cr coated Zr-4 alloy

Deformation and Annealing Behavior of Cr Coating Prepared by Pack-Cementation on the Surface of Austenitic Stainless Steel

Microstructures and corrosion resistance of Fe-based amorphous/nanocrystalline coating fabricated by laser cladding

Chromium Diffusion Coating on an ODS Ferritic-Martensitic Steel and Its Oxidation Behavior in Air and Steam Environments

Investigation on Microstructures and High-Temperature Oxidation Resistance of Cr Coatings on Zircaloy-4 by Multi-Arc Ion Plating Technology

Systematic investigations on the oxidation mechanism of Cr coated Zr-4 alloy under different high-temperature steam conditions

Corrosion Degradation Mechanism of Cr-Coated Zr-4 Alloy under Simulated Nuclear Conditions for Accident-Tolerant Fuel