Abstract:Early nuclear power plant components were normally made with Stainless Steel AISI 316L due to its good anticorrosion property before they are replaced by Inconel 600 or Inconel 690 alloys in recent decades. After long time running, these 316L nuclear components are facing severe intergranular stress corrosion under rigorous radiation conditions. To rejuvenate the as-eroded 316L components is vital for long-term sustainable and safe operation of the nuclear power plants. It is approved that the resistance to intergranular stress corrosion cracking and intergranular attack is significantly dependent on the Cr content in the material. SS316L contains only about 17% Cr while In 690 contains about 30%. Laser deposition of In 690 onto 316L to furbish its corrosion-resistant quality is considered as a practical and cost-effective method. The key issue is how to achieve a coating with enough high chromium content by laser deposition of Inconel 690 onto 316L substrate.This paper focuses on investigation on main factors influencing the Cr content in the coating including the dilution rate, laser types, beam energy distribution and laser processing parameters. Results demonstrate that Nd: YAG laser induces high dilution rate to decrease Cr content much more easily than CO2 laser. A rectangular beam is favorable of low dilution while keeping a high deposition rate than a Gaussian beam. Optimized conditions and processing parameters are necessary to guarantee a high Cr content coating up to 27%, which meets the requirements for practical repairing applications. The coatings with higher Cr content show better anticorrosive property.Early nuclear power plant components were normally made with Stainless Steel AISI 316L due to its good anticorrosion property before they are replaced by Inconel 600 or Inconel 690 alloys in recent decades. After long time running, these 316L nuclear components are facing severe intergranular stress corrosion under rigorous radiation conditions. To rejuvenate the as-eroded 316L components is vital for long-term sustainable and safe operation of the nuclear power plants. It is approved that the resistance to intergranular stress corrosion cracking and intergranular attack is significantly dependent on the Cr content in the material. SS316L contains only about 17% Cr while In 690 contains about 30%. Laser deposition of In 690 onto 316L to furbish its corrosion-resistant quality is considered as a practical and cost-effective method. The key issue is how to achieve a coating with enough high chromium content by laser deposition of Inconel 690 onto 316L substrate.This paper focuses on investigation on main fa...

Corrosion resistance of 316 stainless steel in a simulated pressurized water reactor improved by laser cladding with chromium

Mechanistic understanding of the localized corrosion behavior of laser powder bed fused 316L stainless steel in pressurized water reactor primary water

Correlating oxidation resistance to stress corrosion cracking of 309L and 308L stainless steel claddings in simulated PWR primary water

Investigation on in-situ laser cladding coating of the 304 stainless steel in water environment

Corrosion Resistance of Candidate Cladding Materials for Supercritical Water Reactor

Autoclave grid-to-rod fretting corrosion behaviors of the Zr alloy fuel cladding with and without Cr coating through advanced characterization

Corrosion Performance of He Ion Irradiated 304l Stainless Steel Made by Laser Powder Bed Fusion in Simulated Pwr Water

The Microstructure and Properties of Laser-Cladded Ni-Based and Co-Based Alloys on 316L Stainless Steel

High Chromium Coating by Laser Deposition of in 690 for Repairing Nuclear Power Plant Components

Microstructure and flow accelerated corrosion resistance of Cr coatings electrodeposited in a trivalent chromium bath

Superior Protective Performance of Ni Cr Coating on Stainless Steel 316L in Pure, Oxygenated and Chlorinated Supercritical Water

Characterization of Nickel Cladding on Type 316H Stainless Steel for Enhanced Corrosion Resistance in Molten Chloride Salts

Effects of Y2O3 Content on Wear Resistance and Corrosion Resistance of 316L/TiC Coating Fabricated by Laser Cladding

Effects of composition and microstructure on oxidation and stress corrosion cracking susceptibility of stainless steel claddings in hydrogenated PWR primary water

Microstructure and Corrosion Property of Prepared CoCrW Coatings on the TC4 Surface by Laser Cladding

Enhanced Corrosion Resistance in Accident-Tolerant FeCrAl Alloy by Water-Assisted Laser Surface Modification

Effects of pack chromizing on the microstructure and anticorrosion properties of 316L stainless steel

Comparison and mechanism research of corrosion behavior of materials used in supercritical water-cooled reactors

Corrosion behavior of CoCrNiMoBC coatings obtained by laser cladding: Synergistic effects of composition and microstructure

Research on the Preparation Process and Performance of a Wear-Resistant and Corrosion-Resistant Coating

Effect of Y2O3 Content on Microstructure and Corrosion Properties of Laser Cladding Ni-Based/WC Composite Coated on 316L Substrate