Abstract:Abstract Here, numerous oxygen-containing functional groups were grafted onto the surface of CNTs to improve their dispersibility in an electrolyte. The CNTs were characterized by FT-IR, Raman, XPS, FE-SEM, and TEM. The results revealed that the dispersibility of the functionalized CNTs in the composites was better than unfunctionalized CNTs. CNTs/Ni composites were deposited on a copper plate by pulsed electrodeposition and ultrasonic dispersion using an electrolytic bath with CNTs concentrations from 0 to 2 g l −1 . The friction and wear behavior of the composite coatings were assessed using two different methods. In the first method, the coatings were scratched with a progressively higher load from 0–100 N, and the results demonstrate a 10 percent reduction in the coefficient of friction (COF) of the composite compared to pure nickel. The other method involved applying a constant load of 30 N, the COF and microscopic wear mechanism were investigated at different carbon nanotube contents, and the results confirmed that the COF of the composites was gradually reduced with the increase of carbon nanotube mass concentration, and the COF was only 0.343 when the carbon nanotube content was increased to 2 g l −1 . According to the XRD results, increasing the CNTs contents changed the preferred growth orientation. Moreover, the FE-SEM images of the wear surface of the 1 g l −1 CNTs/Ni sample indicated that it had the best wear resistance and showed the smoothest wear trace without apparent cracks. The addition of CNTs enhanced the wear resistance of the nickel matrix due to the superior mechanical strength and lubricating effect of the CNTs. CNTs exposed to the matrix surface reduced the direct contact between the Ni matrix and the friction pair, acted as lubricants, and reduced the wear rate.

Pulse electrodeposited Ni–C films and its performance

Fabrication and performance of Ni-Co-P/Si3N4 electroplated composite coatings on al-si alloys

Preparation and characterisation of the Ni-C composite coating electrodeposited with carbon sol

SYNTHESIS AND THE PERFORMANCE OF CARBON NANOTUBES-(Ni-P) COMPOSITES

Electrodeposition and Characterization of Nano-Structured Ni–SiC Composite Films

Electrodeposition, microstructure and tribological performance of Ni/(N) incorporated diamond-like carbon films

Investigation of the microstructure and tribological properties of CNTs/Ni composites prepared by electrodeposition

Preparation and Characterization of Pulse Electrodeposited Ni/W-SiC Nanocomposite Coating on Mild Steel Substrate

An Investigation into Electrodeposited Co−Ni−TiO2 Films with Improved Mechanical and Corrosion Properties

Preparation and Investigation of Ni–Co–P Alloy Coatings Using Jet Electrodeposition with Varying Pulse Parameters

Characterization of Pulse Electrodeposited Ni-SiC Nanocomposite Coating on Four Stroke Internal Combustion Engine Cast Iron Cylinder Liner

Effect of Pulse Electrodeposition Mode on Microstructures and Properties of Ni-TiN Composite Coatings

Preparation of Electrodeposited Ni-CNTs Nanocomposite Coatings with Highly Wear and Corrosion Resistance Properties

Super-Low Friction Nickel Based Carbon Nanotube Composite Coating Electro-Deposited from Eutectic Solvents

Electrochemical Properties and XPS Analysis of Ni-B/SiC Nanocomposite Coatings

Friction and wear behaviors of electrodeposited Ni-P-CNTs composite coatings on Al-alloy substrate

Enhancement of Corrosion and Wear Resistance of Ni-P Coatings Stems from the Synergistic Effects of Cr3C2 and Heat Treatment

Preparation of Ni-Cnt Composite Coatings on Aluminum Substrate and Its Friction and Wear Behavior

Enhancing NiCoB alloy coatings with hBN nanoparticles: exploring structural, mechanical, and corrosion improvements through pulse electrodeposition

A Study on the Electrocodeposition Processes and Properties of Ni–SiC Nanocomposite Coatings

Effect of TiN concentration on microstructure and properties of Ni/W–TiN composites obtained by pulse current electrodeposition