Abstract:The effect of nitrogen content on the formation of an equiaxed solidification structure of Fe-16Cr steel was investigated. Moreover, two different kinds of refractory materials, i.e., alumina and magnesia, were employed to control the type of oxide inclusion. The characteristics of TiN(-oxide) inclusions were quantitatively analyzed in both molten steel and solidified samples. When the melting was carried out in the alumina refractory, the grain size continuously decreased with increasing nitrogen content. However, a minimum grain size was observed at a specific nitrogen content (approx. 150 ppm) when the steel was melted in the magnesia refractory. Most of the single TiN particles had a cuboidal shape and fine irregularly shaped particles were located along the grain boundary due to the microsegregation of Ti at the grain boundary during solidification. The type of TiN-oxide hybrid inclusion was strongly affected by the refractory material where Al2O3-TiN and MgAl2O4-TiN hybrid-type inclusions were obtained in the alumina and magnesia refractory experiments, respectively. The formation of oxide inclusions was well predicted by thermochemical computations and it was commonly found that oxide particles were initially formed, followed by the nucleation and growth of TiN. When the nitrogen content increased, the number density of TiN linearly increased in the alumina refractory experiments. However, the number of TiN exhibits a maximum at about [N] = 150 ppm, at which a minimum grain size was obtained in the magnesia refractory experiments. Therefore, the larger the number density of TiN, the smaller the primary grain size after solidification. The number density of TiN in the steel melted in the magnesia refractory was greater than that in the steel melted in the alumina refractory at given Ti and N contents, which was due to the lower planar lattice disregistry of MgAl2O4-TiN interface rather than that of Al2O3-TiN interface. When ∆TTiN (= difference between the TiN precipitation temperature and the liquidus of the steel) was 20 K to 40 K, the number density of effective TiN was maximized and thus, the grain size was minimized after solidification. Finally, although most of the TiN particles were smaller than 1 μm in the molten steel samples irrespective of the nitrogen content, TiN particles larger than 10 μm were observed in the solidified samples when the nitrogen content was greater than 150 ppm. The growth of TiN particles during melting and solidification was well predicted by the combinatorial simulation of the ‘Ostwald ripening model’ based on the Lifshitz–Slyozov–Wagner theory in conjunction with the ‘Diffusion controlled model’ using Ohnaka’s microsegregation equation.

Comparison study on mechanical properties of powder metallurgy titanium materials with nitrogen solutes and TiN dispersoids

Outstanding strength-ductility balance in a Ti–N alloy by tuning ball milling time

TiB Whisker and Nitrogen Solid‐Solution Synergistic‐Strengthened Titanium Matrix Composites by Ti–BN via Spark Plasma Sintering and Hot Extrusion

Microstructure evolution and reactive diffusion behavior of highly dense TiNi alloy prepared from Ti 2 Ni and TiNi 3 intermetallic compound powders

Plasma Nitridation and Mechanical Properties of Pure Titanium Casts

Additive manufacturing of titanium alloys with enhanced strength and uniform ductility via multi-element alloying

A titanium-nitrogen alloy with ultrahigh strength by ball milling and spark plasma sintering

Study on the Preparation of Network Ti-N/Ti Composites by Nitridation of Ti Powders

In-situ Synthesis of TiN and its Effects on Fe-12Cr-6Al in Laser Powder Bed Fusion

First Principles Calculations of the Influence of Nitrogen Content on the Mechanical Properties of Α-Ti

Influence of Ti on the Tensile Properties of the High-Strength Powder Metallurgy High Entropy Alloys

In-situ tensile deformation behavior of powder metallurgy Ti6Al4V alloys

Quantitative strengthening evaluation of powder metallurgy Ti–Zr binary alloys with high strength and ductility

Integrated high-performance and accurate shaping technology of low-cost powder metallurgy titanium alloys: A comprehensive review

Synergistic Effect of Nitrogen and Refractory Material on TiN Formation and Equiaxed Grain Structure of Ferritic Stainless Steel

Control of TiN precipitation behavior in titanium-containing micro-alloyed steel

Advanced tensile properties and strain rate sensitivity of titanium matrix composites reinforced with CaTiO3 particles

Strong and ductile titanium via additive manufacturing under a reactive atmosphere

The Dispersion-Strengthening Effect of TiN Nanoparticles Evoked by Ex Situ Nitridation of Gas-Atomized, NiCu-Based Alloy 400 in Fluidized Bed Reactor for Laser Powder Bed Fusion

Correlation between microstructure and mechanical properties of novel Co-Ni-based powder metallurgy superalloy

Enhanced tensile properties in a Cu-Al2O3 alloy via trace Ti addition