Abstract:Abrasive water jet technology can be used for micro-milling using recently developed miniaturized nozzles. This thesis develops methodologies to predict the shape of micro-channels milled using high pressure abrasive water jets, and presents a new high pressure abrasive slurry jet micro-machining process. Since abrasive water jet (AWJ) machining is often used with both the nozzle tip and workpiece submerged in water to reduce noise and contain debris, the performance of submerged and unsubmerged abrasive water jet micro-milling of channels in 316L stainless steel and 6061-T6 aluminum at various nozzle angles and standoff distances were compared. It was found that the centerline erosion rate decreased with channel depth due to the spreading of the jet as the effective standoff distance increased, and because of the growing effect of the stagnation zone as the channel became deeper. The erosive jet spread over a larger effective footprint in air than in water, since particles on the jet periphery were slowed much more quickly in water due to increased drag. As a result, the width of a channel machined in air was wider than that in water. It was also found that the erosive efficacy distribution changed suddenly after the initial formation of the channel. Then, a new surface evolution model was developed that predicts the size and shape of relatively deep micro-channels up to aspect ratios of 3 resulting from unsubmerged and iv submerged abrasive water jet micro-machining (AWJM) using a novel approach in which two different erosive efficacy expressions were sequentially applied. Since the channels produced by AWJM were found to be relatively wavy due to fluctuations in abrasive mass flow rate, a novel high pressure (water pump pressure up to 345 MPa) abrasive jet slurry micro-machining (HASJM) system was introduced by feeding a premixed slurry into the mixing chamber of a water jet machine with a micro-nozzle. Moreover, an existing model developed for AWJM abrasive particle velocities was modified and used to predict the particle velocity in HASJM, and then verified using a double disc apparatus (DDA). The HASJM system was then used to study the effect of entrained air in abrasive water jet micro-machining (AWJM) by performing experiments at the same particle velocity and dose for the two systems. The centerline waviness, Wa, of micro-channels made in SS316L and Al60661-T6 using HASJM were typically 3.4 times lower than those made with AWJM using the same dose of particles due to the more constant abrasive flow rate provided by the HASJM provided. The centerline roughness, Ra was approximately the same in both processes at a traverse velocity of Vt=4572 mm/min and a nozzle angle of 90°. For micro-channels of a given depth, the widths of those made with HASJM were 25.6 % narrower than those produced with AWJM, mainly due to the wider jet that resulted from the entrained air in AWJM.

Characteristics of multiphase jet machining: A comparison with the absence of water

Improvement of process repeatability and resolution in abrasive air jet machining via viscous slurry entrainment

Numerical Research on Kerf Characteristics of Abrasive Waterjet Machining Based on the SPH-DEM-FEM Approach

Accuracy of the pattern transfer from the metal mask to the workpiece surface during multiphase jet machining

Modeling of the Cutting Front Profile in Abrasive Water Jet Machining Based on the Energy Balance Approach

Surface removal of ductile metal using cyclic low-frequency impact of a discrete particle-less waterjet

Experimental and simulation study on the influence factors of abrasive water jet machining ductile materials

Micro-channel milling using abrasive waterjets and high pressure abrasive slurry jets

Coaxial helical gas assisted laser water jet machining of SiC/SiC ceramic matrix composites

A review of additives in abrasive water jet machining and their performance

The effect of cutting jet variation on striation formation in abrasive water jet cutting

Erosion characteristics of water droplet machining

Hole characteristics and surface damage formation mechanisms of C /SiC composites machined by abrasive waterjet

Towards an Understanding of Multiphase Fluid Dynamics of a Microfluid Jet Polishing Process: A Numerical Analysis

Towards understanding the influence of process parameters during the abrasive jet machining of cemented carbides via response surface method

Mechanism of C /SiC hole making with high shape precision using abrasive waterjet based on response surface method

Numerical and experimental study on the flow characteristics and the erosive ability of magnetorheological jet

Ultrasonic Machining: A Total Mechanical Machining Technology Using Loose Abrasive Particles

Research on Multiphase Flow and Nozzle Wear in a High-Pressure Abrasive Water Jet Cutting Head

Investigation on the Coaxial-Annulus-Argon-Assisted Water-Jet-Guided Laser Machining of Hard-to-Process Materials

Experimental Investigation and Molecular Dynamics Simulation of Contributing Variables on Abrasive Water Jet on Aluminum Alloy 7075 Reinforced with Al2O3, Graphite and Silicon Carbide