Abstract:Abrasive water jet (AWJ) is a type of cold processing technology, and there are many factors affecting its machining effect. In this paper, a coupled Finite Element Methods-Smoothed Particle Hydrodynamics (FEM-SPH) numerical model was established to investigate the key influencing factors of AWJ machining ductile materials. The abrasive particles in the model were shaped as irregular polyhedrons, and the material properties of the abrasive particles as well as the influence mechanism of the fluid–structure interaction between the abrasive particles and the water were considered. The relative error range of experimental measured results and simulation predicted results is 22.77%–36.55%. Then, the effects of content and distribution of abrasive particles, the jet working pressure P, the traverse rate of nozzle V t r a v and the impingement angle α were systematically and quantitatively evaluated through two-way verification of experiments and simulations. It was found that: (i) Effects of stand-off distance (SOD) on the kerf profile and the quality of kerf surface was essentially determined by the content and distribution of abrasive particles. As the increase of SOD, the jet divergence gradually increases, and the kerf profile gradually changes from “U-shaped” to “V-shaped”. (ii) Experiments and simulations demonstrate that the P has a linear increasing relationship with the maximum depth h of kerf profile, and the V t r a v has a linear decreasing relationship with the maximum depth h, while it has a linear increasing relationship with the jet trailing angle β , which was independent of the ductile material type. (iii) The combined effect of V t r a v and α affects geometric parameters and surface quality of the kerf profile, under the same P, the depth of the cut surface obtained by backward cutting is only 72.1% of that of the forward cutting, while the quality of the cut surface of former one is higher than the latter one.

Towards understanding the influence of process parameters during the abrasive jet machining of cemented carbides via response surface method

Enhancing High-Alloy Steel Cutting with Abrasive Water Injection Jet (AWIJ) Technology: An Approach Using the Response Surface Methodology (RSM)

Experimental and simulation study on the influence factors of abrasive water jet machining ductile materials

Characterization and Optimization of Abrasive Water Jet Machining Parameters of aluminium/silicon carbide Composites

Design for Manufacturing of Cemented Carbide Coated Components Toward High Wear and Impact Resistance Performance

Improvement of process repeatability and resolution in abrasive air jet machining via viscous slurry entrainment

Experimental study on the machining performance of nickel-based superalloy GH4169 milled by AWJ

Process Parameter Modeling and Optimization of Abrasive Water Jet Dressing Fixed-Abrasive Pad Based on Box–Behnken Design

Accuracy of the pattern transfer from the metal mask to the workpiece surface during multiphase jet machining

Analysis and optimization of abrasive waterjet dressing parameters for surface texturing of diamond grinding wheels

Experimental investigation on the effet of input paramètres on surface roughness and MRR of abrasive flow machining process

Mechanism of C /SiC hole making with high shape precision using abrasive waterjet based on response surface method

A novel quantitative analysis approach for hole surface damage of ceramic matrix composites machined by abrasive waterjet

Enhancing the grinding performance of RB-SiC ceramic using abrasive water jet dressed diamond grinding wheels

Investigation on the Coaxial-Annulus-Argon-Assisted Water-Jet-Guided Laser Machining of Hard-to-Process Materials

Modelling and experimental study of surface treatment in abrasive waterjet peening of Nickel-based superalloy: Inverse problem

Effect of process parameters of Plain Water Jet on the cleaning quality, surface and material integrity of Inconel 718 milled by Abrasive Water Jet

Simultaneous optimization of process parameters during abrasive water jet machining on glass fibre reinforced polymer

Material response to particle impact during abrasive jet machining of alumina ceramics

An Experimental Investigation on Machining of Hardened AISI 440C Stainless Steel Using Abrasive Water Jet Machining Process

AWJ machining of high-volume fraction SiCp/Al composites