Abstract:Purpose: The purpose of this study was to review the literature regarding the evolution of current thoughts on fixation of mandibular angle fractures (MAFs), based on in vitro biomechanical assessments and computer-based studies. Methods: An electronic search in PubMed was undertaken in August 2012. The titles and abstracts from these results were read to identify studies within the selection criteria. Eligibility criteria included studies from the last 30 years (from 1983 onwards). Results: The search strategy initially identified 767 studies. Thirty-one studies were identified without repetition within the selection criteria. Two articles showing significance in the development of treatment techniques was included. Additional hand searching yielded five additional papers. Thus, a total of 38 studies were included. Conclusions: The osteosynthesis positions as well as the plating technique play important roles in the stability of MAF repair. The only in vitro study evaluating the use of wire osteosynthesis concluded that wires placed through the lower border approach would provide greater stability than those at the upper border. Many studies indicate that the use of two miniplates avoids (or decreases) lateral displacement of the lower mandibular border and opening of the inferior fracture gap. Some studies even suggest that the use of two miniplates may be considered a more "rigid" fixation technique for MAFs than the use of a reconstruction plate. When using two miniplates, the biplanar plate orientation provides greater biomechanical stability than the monoplanar one. However, despite its greater biomechanical stability, the two-miniplate technique has some disadvantages that should also be taken into account. Studies with biodegradable plates suggest the use of at least two plates for each MAF. There are few studies with compression plates, and they have not yet reached a consensus. The solitary lag screw proved to withstand the functional loading of the mandible; however, only few biomechanical assessments were performed. In vitro studies have shown good biomechanical stability with the use of 3-D grid plates. The use of malleable miniplates alone is not sufficient to withstand the early postoperative bite force. Some studies suggest that the segment of the tension band miniplate located at the distal fragment of the MAF should be fixed with three screws. The studies also showed some limitations. None considered the stabilization of the fracture site afforded by the masseter-pterygoid muscle pouch. Most of the studies did not evaluate plating system strength in the long term and therefore did not observe the effect of resorption on the strength of the different biodegradable plating systems. Another limitation of many studies is the absence of a control group. A confounding factor that could not be tested in in vitro investigations is the additional resistance to displacement of jagged fracture margins present in the human fracture.

Modeling stability post zygomatic fracture reconstruction

Stress analysis on three dimensional finite element model of zygomatic complex fracture fixation

Stability of different fixation methods after reduction malarplasty under average and maximum masticatory forces: a finite element analysis

Fixation of mandibular angle fractures: in vitro biomechanical assessments and computer-based studies

Biomechanical assessment of mandibular fracture fixation using finite element analysis validated by polymeric mandible mechanical testing

Feasibility of 2-Point Fixation by Absorbable Plates Using the Transoral Approach in Management of the Zygomatic Complex Fractures

Role of finite element analysis for selection of single point fixation in zygomaticomaxillary complex fracture

Preoperative evaluation and surgical technique of functional and cosmetic aspects in zygomatic complex fracture patients

Finite Element Analysis of Two- and Three-Dimensional Fixation in Treating Mandibular Symphyseal Fracture Combined with Bilateral Condylar Intracapsular Fractures.

Stability of midface fracture repair using absorbable plate and screw system pilot holes drilled and pin placement at angles other than 90°

New Innovation: Custom Titanium Zygomaticomaxillary Complex (ZMC) Plate for Facial Reconstruction

Biomechanical Study on the Comparison of Synthetic Materials for Cranio-Orbital Fracture Repair

Biomechanical analysis of mandibular defect reconstruction based on a new base-fixation system

Experimental validation of finite element simulation of a new custom-designed fixation plate to treat mandibular angle fracture

Assessment of different treatment alternatives for patients with total maxillectomy

Evaluation of grafts fixation techniques for temporomandibular joint reconstruction with medial femoral condyle flap: A numerical study

Functional stability analyses of maxillofacial skeleton bearing cleft deformities

Three-dimensional secondary reconstruction of mistreated zygomatic fractures using patient specific surgical guides and implants

Biomechanical evaluation of various rigid internal fixation modalities for condylar-base-associated multiple mandibular fractures: A finite element analysis

Mandibular biomechanics rehabilitated with different prosthetic restorations under normal and impact loading scenarios

Biomechanical comparison of plate materials and designs for subcondylar fracture fixation: An assessment