Abstract:During the past few decades, various organic aerogels (AGs) have been synthesized and shown a number of exceptional and even unique properties, such as low bulk density, high porosity, great surface areas, and extremely low thermal conductivity, which enable them being the focus of industry and academia. Thus, AGs exhibit substantial performance boosts in numerous applications such as adsorption, separation, catalysis, energy conversion and storage, and so on. Regrettably, AGs generally exhibit high cost, poor thermal and mechanical properties, which seriously restrict their large-scale applications. In this study, ceramic was introduced into commercial available resin derived aerogel due to the enhancement of silicon to thermal stability and low cost of the resin. Silica ceramic modified phenolic resin (PR-SiO2) aerogel was synthesized by a simple sol-gel polymerization of ceramic precursor, PR, hexamethylenetetramine in an ethylene glycol solution, followed by solvent exchange and ambient pressure drying. The modified effect on the porous structure, textural property, and thermal stability was studied by scanning electron microscope (SEM), nitrogen adsorption isotherms, and thermogravimetric analysis (TGA). According to the characterizations of SEM and nitrogen adsorption, the obtained PR-SiO2 hybrid aerogels have a continuous three dimensional network that consists of phenolic nano-particles and curved nano-sheets with size from 50 to 90 nm, which define numerous mesopores and macropores. TGA in argon atmosphere indicated that the thermal stability of the PR-SiO2 aerogels (both maximum decomposition rate and char yield at 1000 degrees C) is better than that of the pristine PR aerogel. In order to improve the mechanical properties, carbon fabric reinforced aerogel composite was prepared by impregnating carbon-bonded carbon fiber (CBCF) composite with the aerogels. In the micrographs of the aerogel matrix composite, the aerogels are fully and uniformly occupied the void between carbon fibers, and coated with a thin layer on the fiber surface. Moreover, a homogeneous morphology without cracking and fracture was obtained at the fiber/resin interface, as the appropriate porous structure and enough strength of the aerogel networks to decrease and withstand the capillary pressure at the liquid/gas interface during the drying at ambient pressure, prevent the aerogel networks from collapse. Due to the low bulk density (0.18g/cm(3)), high porosity (similar to 90%) and unique fiber geometry (a typical 2D planar random structure with the carbon fibres in the xy direction are distributed homogeneously in plane, while in the z direction over the height of the composite) of the CBCF fabric, the obtained composite possessed low bulk density (0.32- 0.45 g/cm(3)), high compressive strength (0.8-2.8 MPa for different directions) and low thermal conductivity (0.098-0.148 W/(mK)). More importantly, good thermal ablative and insulative properties in oxy-acetylene flame simulated high temperature environment (linear ablation rate as low as 0.085 mm/s, internal temperature peaks below 200 degrees C at 38 mm in-depth position as the surface temperature approximately 1800 degrees C). Therefore, the novel lightweight aerogels and composites are excellent heat-insulation and thermal-protection materials with applications in the fields of energy-saving and aerospace.

Novel atmospheric pressure drying method for silica-based aerogel insulation: Inspired with the adult process of damselflies

Enhancing Mesopore Volume and Thermal Insulation of Silica Aerogel via Ambient Pressure Drying-Assisted Foaming Method

High Compression Strength and Thermal Insulation Silica Aerogel Monolith with Scaffold of a Cyclic Olefin Siloxane Co-Oligomer Via Ambient Pressure Drying

In-situ acid catalysis strategy to achieve rapid ambient pressure drying preparation of aerogels

Synthesis and Characterization of Silica Aerogel and Its Composite Materials

A novel low-cost method of silica aerogel fabrication using fly ash and trona ore with ambient pressure drying technique

Preparation of Silica Aerogels Via Ambient Pressure Drying

Preparation of high-strength silica aerogels by two-step surface modification via ambient pressure drying

Breakthroughs in cost-effective, scalable production of superinsulating, ambient-dried silica aerogel and silica-biopolymer hybrid aerogels: from laboratory to pilot scale

Fumed Silica-Derived, Ambient Dried, and Low-Cost Nanoporous Aerogel-like Monoliths for Thermal Insulation

Preparation of the methyltriethoxysilane based aerogel monolith with an ultra-low density and excellent mechanical properties by ambient pressure drying

A Facile Strategy for Freeze-Drying Preparation of Silica Aerogel from Sodium Silicate

Synthesis and characterization of silica aerogels by a novel fast ambient pressure drying process

Facile Synthesis of Flexible and Hydrophobic Polymethylsilsesquioxane Based Silica Aerogel Via the Co-Precursor Method and Ambient Pressure Drying Technique

Ultrahigh-strength silicone aerogels reinforced by an armor-like epoxy framework via a temperature-controlled sequential reaction strategy

Ambient-pressure drying synthesis of large resorcinol–formaldehyde-reinforced silica aerogels with enhanced mechanical strength and superhydrophobicity

Characterization, Mechinical, Thermal And Ablative Properties Of Ceramic Modified Phenolic Resin Aerogels Synthsized By Ambient Pressure Drying

Mechanically strong and thermal insulating polyimide/SiO2 aerogel prepared by ambient drying

Ambient Pressure Drying as an Advanced Approach to the Synthesis of Silica Aerogel Composite for Building Thermal Insulation

Aramid Fibers Reinforced Silica Aerogel Composites with Low Thermal Conductivity and Improved Mechanical Performance

Convenient and rapid preparation of aerogels dried at ambient pressure