Abstract:Silicon nitride (Si3N4) powder possesses a high refractive index and a significant ultraviolet (UV) absorptivity, consequently enabling great challenges in the fabrication of Si3N4 ceramics using vat photopolymerization. The TEM, SEM, XRD and XPS results indicate that the yttrium aluminum garnet (YAG) can be coated on the surface of Si3N4 ceramic powder using a non-aqueous chemical precipitation coating (NCP) process, and the effects of ceramic powder coating treatment on the curing behavior, rheological of Si3N4 slurry, and the microstructure and mechanical properties of Si3N4 ceramics were systematically investigated in this work, based on the detailed performance comparisons between the Si3N4 samples manufactured using the NCP and traditional wet ball-milling (WBM) methods, respectively. Results demonstrated that the uniform distribution of YAG film on the surface of Si3N4 powder notably can favor the enhancement of the rheological and curing behaviors of Si3N4 ceramic slurries. The viscosity of NCP ceramic slurry was observed to be 42.25 % lower than that of WBM ceramic slurry at a shear rate of 35 s(-1). Additionally, the cure depth of NCP ceramic slurry with the solid loading of 30 vol% at the exposure energy of 159.6 mJ/cm(2) was measured to be 35.4 mu m, which is 22.49 % higher than that of the WBM ceramic slurry. Moreover, compared with the WBM ceramic slurry at the same curing depth, the NCP ceramic slurry demonstrates higher precision in shaping dimensions. The bending strength and Weibull modulus of NCP-SN sample were 833.74 +/- 39.35 MPa and 25.15, respectively, which were 17.64 % and 173.07 % higher than those of WBM-SN sample. This improvement is attributed to the advantageous aspects of the NCP process, which promote the uniform distribution of the liquid phase, facilitate the sintering densification of Si3N4 ceramic, and accelerate the formation of elongated crystalline grains. Ultimately, superior-quality Si3N4 components with distinct contours were successfully fabricated. The methodology proposed in this work contributes to advancing the rapid manufacturing and performance optimization of the intricately structured Si3N4 ceramic components.

Enhanced curing behavior, mechanical and thermal properties of 3D printed aluminum nitride ceramics using a powder coating strategy

Fabrication of High Thermal Conductivity Aluminum Nitride Ceramics via Digital Light Processing 3D Printing

Effects of Ceramic Powder Coating Treatment on the Curing Behavior, Mechanical Properties, and Microstructure of 3D Printed Silicon Nitride Ceramics

High-performance aluminum nitride made by Vat photopolymerization through optimization of resin refractive index and plasticizer content

Thermal conductivities and mechanical properties of AlN ceramics fabricated by three dimensional printing

Additive manufacturing of complex-shaped and high-performance aluminum nitride-based components for thermal management

Optimizing AlN hydrolysis process to fabricate coated modified powders for improving the properties of Si 3 N 4 /SiAlON ceramics prepared by Vat Photopolymerization

Microstructure refinement-homogenization and flexural strength improvement of Al2O3 ceramics fabricated by DLP-stereolithography integrated with chemical precipitation coating process

Effect of particle size on rheology, curing kinetics, and corresponding mechanical and thermal properties of aluminum nitride (AlN) ceramic by digital light processing (DLP)-based vat photopolymerization

Mechanical and dielectric properties of Si3N4/β-SiAlON composite ceramics fabricated by vat photopolymerization 3D printing technology

Effect of particle size distribution and printing parameters on alumina ceramics prepared by Additive Manufacturing

Investigation of curing behavior and mechanical properties of SiC ceramics prepared by vat photopolymerization combined with pressureless liquid-phase sintering using Al 2 O 3 -coated SiC powder

Preparation of high performance dense Al 2 O 3 ceramics by digital light processing 3D printing technology

Impact of Sintering Aid Type and Content on the Mechanical Properties of Digital Light Processing 3D-Printed Si3N4 Ceramics

The influence mechanism of nano-alumina content in semi-solid ceramic precursor fluid on the forming performance via a light-cured 3D printing method

Dynamic mechanical properties of Alumina prepared by vat photopolymerization based on high solid loading slurry

In-situ Y3Al5O12 enhances comprehensive properties of alumina-based ceramic cores by vat photopolymerization 3D printing

Microstructures and mechanical properties of additively manufactured alumina ceramics with digital light processing

Vat Photopolymerization 3D Printing of Alumina Ceramics with Low Sintering Temperature

Fabrication of Electrical Semi-Conductive SiCN Ceramics by Vat Photopolymerization

Design of 3D printed bioinspired nacre-like structured materials with significantly enhanced thermal conductivity