Abstract:The three-dimensional grain-averaged response of solid bar samples under non-proportional (NP) elastoplastic axial-torsional loading was investigated using in situ high energy diffraction microscopy (HEDM) and companion crystal plasticity finite element (CPFE) modeling. Important stress metrics including applied shear (σ θZ ) and axial (σ ZZ ) stress tensor components, stress and stress deviator tensor invariants (I 1 , J 2 , and J 3 ), von Mises equivalent stress (), maximum resolved shear stress (mRSS), stress triaxiality (η), and lode angle parameter () values were tracked for ∼ 300 grains under two different loading conditions: (1) Torsion-dominated loading (low NP) and (2) Tension-torsion loading (high NP) in equiatomic NiCoCr, a representative multicomponent face-centered cubic (FCC) superalloy. Overall, significant stress localizations existed within both samples as evidenced by the radial dependence of grain-resolved σ θZ , , and J 2 ; by comparison, I 1 , J 3 , η, and metrics did not show discernable trends within the volume. These stress localizations reveal a complex interplay between axial and shear stress components (e.g., stress coupling) resulting in grain yielding near the sample surface largely driven by shear stress, whereas internal grain yielding was largely accommodated by axial stress. Grain-resolved stress localization trends were described well by the CPFE model, although some discrepancies in magnitude occurred, particularly for volumetric stress metrics (I 1 and η) due to initial type II residual stress distributions. The superposition of initial residual stress states onto CPFE grain-resolved data significantly improved model accuracy for η. This suggests that residual stresses more strongly influence the simulation of volumetric rather than deviatoric (yield) stress metrics.

A study of stress, composition and grain interaction gradients in energy‐dispersive X‐ray stress analysis on materials with cubic symmetry

Method to Analyze and Evaluate the Depth Profile of the Three Dimensional Residual Stresses State with X-ray

Stress induced precipitates microstructure in the anisotropy alloys

Stress evolution in plastically deformed austenitic and ferritic steels determined using angle- and energy-dispersive diffraction

Stress analysis of polycrystalline thin films and surface regions by X-ray diffraction

FFT-based investigation of the shear stress distribution in face-centered cubic polycrystals

Intergranular normal stress distributions in untextured polycrystalline aggregates

Intergranular stress distributions in polycrystalline aggregates of irradiated stainless steel

In situ measurement of three-dimensional intergranular stress localizations and grain yielding under elastoplastic axial-torsional loading

A complete grain-level assessment of the stress-strain evolution and associated deformation response in polycrystalline alloys

Analysis of Phase-Specific Strain Pole Figures for Duplex Steels under Elasto-Plastic Uniaxial Tension—Experiment vs. EPSC Modelling

X-ray Diffraction for the Determination of Residual Stress of Crystalline Material: An Overview

Residual Stress of Individual Aluminum Grains from Three Dimensional X-Ray Diffraction

Neutron diffraction methods for the study of residual stress fields

Microstrain and grain-size analysis from diffraction peak width and graphical derivation of high-pressure thermomechanics

X-ray Diffraction Stress Analysis of Ferroelectric Thin Films with Ideal (hkl) Textures Considering the Piezoelectric Coupling Effect

Effect of residual stress in gradient-grained metals: Dislocation dynamics simulations

In Situ Analysis of Stress and Microstructure Evolution during Welding of High-Alloy Steels Using Energy-Dispersive X-Ray Diffraction

Synchrotron-based high-energy X-ray diffraction and microdiffraction investigations on the mechanical heterogeneity of heterostructured metals

Strains and Stresses in Multilayered Materials Determined Using High-Energy X-ray Diffraction

Is stress concentration relevant for nanocrystalline metals?