Abstract:Developing effective strategies for enhancing the damage tolerance of laser powder bed fusion (LPBF) components remains a formidable challenge in the disruptive additive manufacturing field. The typical shot-peening (SP) is a promising and efficient post-treatment procedure owing to its capability to introduce compressive residual stress, enhance the surface integrity, shrinkage the subsurface lack-of-fusion (LoF) defects of LPBF components. However, there is still a significant gap in understanding the appropriate utilization of the SP procedure to enhance fatigue performance, hindering its full potential in practical applications. This study systematically investigated the influence of surface coverage (150 %, 300 %, and 450 %) on surface characteristics, subsurface characteristics, and mechanical properties of LPBF 304L austenitic steel. Though evaluating the feasibility of severe shot peening and observing post-deformed microstructures, the process-microstructure-performance relationship of shot-peened LPBF austenitic steel was preliminarily established for the first time. The results indicated that increasing surface coverage up to a threshold (300 % in this work) could effectively enhance the strength and fatigue performance without significantly sacrificing ductility, primarily attributed to the increased gradient strain generated by the gradient deformation structures as well as the shrinkage of detrimental near-the-surface defects. The excessive surface coverage may be detrimental to ductility and fatigue performance, as it directly increases the severe plastic deformation and near-saturated micro-defects in the gradient deformation layer, substantially weakening the strain gradient's capability to accommodate dislocation flow during deformation. The findings suggested careful selection of shot peening coverage to balance enhanced mechanical properties and minimal introduction of detrimental defects.

Effect of Shot Peening Duration on Microstructure and Mechanical Properties of GH4169 Alloy Prepared by 3D Printing

Effect of shot peening strengths on microstructure and mechanical properties of 316L stainless steel prepared by 3D printing

Mechanical Properties and Fracture Behavior of Laser Powder-Bed-Fused GH3536 Superalloy

Effect of ultrasonic shot peening on microstructure and mechanical properties of GH3230 superalloy during selective laser melt solution heat treatment

Effects of ultrasonic shot peening process on the microstructure and mechanical properties of nickel-based superalloys formed by selective laser melting

In-situ Study of Microstructure and Mechanical Properties of GH3536 Alloy Manufactured by Selective Laser Melting at 750 °C

Influence of shot peening on the microstructure and high-temperature tensile properties of a powder metallurgy Ni-based superalloy

Microstructure and Nanoindentation Hardness of Shot-Peened Ultrafine-Grained Low-Alloy Steel

Comparative study of the effects of conventional shot peening and ultrasonic shot peening on very high cycle fatigue properties of GH4169 superalloy

Influence of Ageing Treatment on Microstructure and Mechanical Properties of GH4169 Alloy Prepared Using Wire Arc Additive Manufacturing

The Effects of Shot Peening parameters on the subsurface properties of AA 7075 T 6 aluminum alloy

Shot peening coverage effect on laser powder bed fused steel

Tribological behavior and surface characteristics of severe surface plastic deformed as-cast and 3D-printed SS316L using LSP

The Influence of Age Hardening and Shot Peening on the Surface Properties of 7075 Aluminium Alloy

Effects of shot peening on microstructure evolution and mechanical properties of surface nanocrystal layer on titanium matrix composite

Microstructural characteristics and enhanced mechanical properties of 2024 aluminum alloy resulting from shot-peening treatment

Revealing the relationship between the shot type and fatigue performance of laser powder bed fused 304L steel following shot peening

Surface mechanical property and residual stress stability of nanostructured CNT/Al-Cu-Mg composites induced by shot peening

Effect of shot peening on surface characteristics and high-temperature corrosion behaviour of super 13Cr martensitic stainless steel

Investigation of Wet Shot Peening on Microstructural Evolution and Tensile-Tensile Fatigue Properties of Ti-6Al-4V Alloy

Effect of Severe Shot Peening on Mechanical Properties and Fatigue Resistance of Wire Arc Additive Manufactured AISI 316L