Abstract:This paper presented a novel study of the preparation of ZrB 2 -enhanced NiCrBSi coatings and its microstructure and tribological properties. NiCrBSi-ZrB 2 composite powder and coatings with ZrB 2 contents of 20 %, 40 %, and 50 % were prepared by spray-drying and high-velocity oxygen-fuel (HVOF) spraying, respectively. The microstructure and high-temperature wear performance at 700 °C were compared with those of an NiCrBSi coating. The results showed that the NiCrBSi and ZrB 2 powder exhibited good wetting properties in the solid-liquid sintering zone and the CrB phase was formed in the liquid phase contact zone in composite coatings with ZrB 2 contents of 20 % and 40 %, while the CrB phase disappeared in the 50 %ZrB 2 coating due to the pinning effect caused by excessive ZrB 2 . The microhardness of composite coatings tended to increase, then decrease, and the 40%ZrB 2 coating reached a maximum hardness of 874 HV. The NiCrBSi coating presented oxidative wear and adhesive wear. Although the fracture toughness of composite coatings was lower than that of the NiCrBSi coating, the wear resistance in the composite coating was significantly enhanced due to the evenly distributed ZrB 2 and CrB phases. The 20%ZrB 2 coating with low fracture toughness and the 50 %ZrB 2 coating with hardness mismatch caused by the absence of CrB produced severe abrasive wear. The hardness gradient with the matrix, ZrB 2 and CrB phases reduced abrasive wear caused by peeling in 40%ZrB 2 coating, and the ceramic phases acted as skeletons reducing the deformation of the load contact area. The formation of Cr 2 O 3 during the friction process further improved the wear resistance. The wear mechanism of 40%ZrB 2 coating underwent light adhesive wear, mild abrasive wear and oxidative wear, and the coating exhibited the best wear resistance with the lowest wear rate of 1.16 × 10 −13 m 3 /N·m (a decreased of 56 %).

Toughening mechanism of in-situ synthesized ZrB2 based composite coating by plasma spraying

Microstructure characterization of in-situ ZrC composite coating with graceful toughness and improved tribological properties prepared by plasma spraying

Microstructure and properties of in-situ ZrB2-ZrC composite coatings by plasma spraying

TEM characterization and toughening mechanism of in-situ NbB2-NbC-Al2O3 composite coatings prepared by plasma spraying

Microstructure and properties of CrB2-Cr3C2 composite coatings prepared by plasma spraying

In-situ synthesis, microstructure, and properties of NbB2-NbC-Al2O3 composite coatings by plasma spraying

In-situ synthesized nanostructured t-ZrO2/La2(Zr0.75Ce0.25)2O7 composite thermal barrier coatings

Microstructure and properties of Al2O3–ZrO2–TiO2 composite coatings prepared by plasma spraying

Microstructure and Ablation Behavior of W Coating Prepared by Atmospheric Plasma Spraying for Zr/Cu Infiltrated C/C Composites

Microstructure and tribological properties of ZrB 2 -enhanced NiCrBSi coatings prepared by high-velocity oxy-fuel spraying

Effect of nano‐Al 2 O 3 on the microstructure and properties of NbB 2 ‐NbC composite coatings prepared by plasma spraying

Microstructure, formation mechanism and properties of plasma-sprayed Cr7C3—CrSi2—Al2O3 coatings

Formation of high heat resistant coatings by using gas tunnel type plasma spraying

Ablation behavior of high-entropy boride (Hf-Zr-Ta-Ti)B 2 coating fabricated via supersonic atmospheric plasma spraying for carbon/carbon composites

Comparison of plasma sprayed NbB2-NbC coatings obtained by ex-situ and in-situ approaches

Microstructure and Ablation Behavior of W/ZrC/SiC Coating on C/C Composites Prepared by Reactive Melt Infiltration and Atmospheric Plasma Spraying

Friction and wear characteristics of in-situ Cr+(Cr,Al)2O3 composite coating fabricated by plasma spraying

Oxidation ablation resistance of ZrB2-HfB2-SiC-TaSi2 coating prepared on C/C composite surface

Microstructure and properties of niobium carbide composite coatings prepared by plasma spraying

Synthesis of In Situ ZrB2-SiC-ZrC Coating on ZrC-SiC Substrate by Reactive Plasma Spraying

Enhanced high temperature ablation resistance of dense ZrB2–Al2TiO5 composite coating by very low-pressure plasma spraying