Abstract:The increasing demand for high-performance aircraft engines has led to a greater emphasis being placed on advanced sealing coating technologies. Developing long-life, self-lubricating, and wear-resistant coatings is of significant research value. This study focuses on the fabrication of a novel self-lubricating and wear-resistant NiCoCrAlY-Cr2O3-AgMo composite coating. This coating was deposited onto a GH4169 substrate utilizing plasma spraying. Scanning electron microscopy with energy-dispersive X-ray spectroscopy (SEM-EDS) and X-ray diffraction (XRD) methods were employed to characterize the elemental composition and microstructure of the fabricated NiCoCrAlY-Cr2O3-AgMo composite coating. Microhardness measurements across the coating cross-section indicated a gradual increase in hardness from the GH4169 substrate to the NiCoCrAlY-Cr2O3-AgMo coating. The average hardness of the GH4169 substrate was 413.92 HV0.2, while the CoNiCrAlY bonding layer region exhibited an average hardness of 467.60 HV0.2. The NiCoCrAlY-Cr2O3-AgMo coating itself demonstrated an average microhardness of 643.22 HV0.2. Room temperature friction tests indicated that the average coefficient of friction (COF) of the GH4169 substrate was 0.665. In contrast, the NiCoCrAlY-Cr2O3-AgMo coating exhibited a significantly lower average COF of 0.16, representing a 75.94% reduction compared to the uncoated GH4169 substrate. High-temperature friction tests were conducted at 400 °C, 500 °C, and 600 °C, indicating average COF values of 0.438, 0.410, and 0.268, respectively, for the NiCoCrAlY-Cr2O3-AgMo coating. Specifically, at 600 °C, the formation of a lubricious NiMoO4 tribofilm on the coating surface was observed. This tribofilm effectively reduced the wear rate of the GH605 pin to 2.78 × 10−6 mm3/N·m, highlighting the potential of the NiCoCrAlY-Cr2O3-AgMo coating to reduce wear in high-temperature sliding contact applications.

Friction and wear characteristics of in-situ Cr+(Cr,Al)2O3 composite coating fabricated by plasma spraying

Microstructure and tribological properties of Al-30Si-5Cu composite coating reinforced with ceramic phases synthesized in situ by plasma spraying

Microstructure, formation mechanism and properties of plasma-sprayed Cr7C3—CrSi2—Al2O3 coatings

Tribological Behavior of Plasma Sprayed Al–Cu–Fe + Sn Quasicrystalline Composite Coatings

Fundamental understanding on the microstructure and corrosion resistance of Cr-(Cr, Al)2O3 composite coatings in-situ synthetized by reactive plasma spraying

Microstructure characterization of in-situ ZrC composite coating with graceful toughness and improved tribological properties prepared by plasma spraying

Microstructure and properties of CrB2-Cr3C2 composite coatings prepared by plasma spraying

The alloying effects of Cr on in-situ phase evolution and wear resistance of nickel composite coatings fabricated by wide-band laser deposition

Preparation and characterization of supersonic plasma sprayed Al–Al2O3–Cr2O3 composite coatings on magnesium alloy substrate

Plasma Spraying NiCoCrAlY-Cr2O3-AgMo Coatings: Fabrication and Tribological Mechanisms

Effect of nano‐Al 2 O 3 on the microstructure and properties of NbB 2 ‐NbC composite coatings prepared by plasma spraying

Microstructure and properties of molybdenum composite coatings by plasma spraying of Mo–SiC and MoO 3 –Al–SiC composite powders

Deposition and properties of plasma sprayed NiCrCoMo–TiC composite coatings

Microstructure, mechanical properties and tribological behaviors of TiAlN-Ag composite coatings by pulsed magnetron sputtering method

Wear performance of the plasma sprayed fine WC-Co composite powders coatings

Microstructure and properties of Al2O3–ZrO2–TiO2 composite coatings prepared by plasma spraying

Microstructure and Properties of Al2O3-13wt.%TiO2-Reinforced CoCrFeMnNi High-Entropy Alloy Composite Coatings Prepared by Plasma Spraying

Effect of Cr3C2 Content on the Microstructure and Wear Resistance of Fe3Al/Cr3C2 Composites

Microstructure and wear behaviour of in-situ TiN-Al2O3 reinforced CoCrFeNiMn high-entropy alloys composite coatings fabricated by plasma cladding

Abrasive wear characteristics of plasma sprayed nanostructured alumina/titania coatings

Microstructure and properties of Cr7C3-CrSi2 composite coatings prepared by plasma spraying