Abstract:Abstract Scale-up studies of fluidized beds are important for numerous fields. Fluidization in a multi-ring inclined nozzle spout-fluid bed (MRIN spout-fluid bed) is one of the most critical factors that affect the coating efficiency and uniformity of tri-structural isotropic (TRISO) nuclear particles in the fluidized bed chemical vapor deposition (FB-CVD) process. In this work, the flow pattern similarity principle was proposed to scale up a specially designed spout-fluid bed, which was aimed at maintaining the gas-solid contact efficiency, and was validated by electrical capacitance tomography (ECT) measurements. First, the traditional ECT method was developed for the specially designed MRIN spout-fluid bed according to the filling method. Then, the reconstruction algorithms were updated using the alternating direction multiplier method (ADMM) by introducing optimization constraints. The fluidization laws were investigated for different superficial gas velocities and distributor structures. We found that the gas distributor structure affected the merge point of the jets, which played an essential role in fluidization pattern changes. The statistically-based coefficient of variation (Cv) was proposed to distinguish the different flow patterns. Multi-ring spouting was then selected as a typical flow pattern for good fluidization and mixing, where the Cv ranged from 0.25 to 0.65. Then, the optimal design principles for the enlarged spout-fluid bed gas distributor were obtained. We determined that a smaller nozzle diameter (0.71 d 0 ), larger nozzle spacing (1.12 x 0 ), and slightly inclined angle (1.50 θ 0 ) could improve fluidization, and that nozzle spacing was the most important factor. This study may be beneficial for the industrial design of the FB-CVD process and for the fabrication of high-density nuclear fuel particles. Additionally, it could be presented to a more general audience for scaling-up fluidized beds with a complex distributor, which would be beneficial for the fluidization research community.

Effect of combining multi-jet component with axial swirl blade on evaporation in a spouted bed

Effect of Agitation on the Fluidization Behavior of a Gas–solid Fluidized Bed with a Frame Impeller

Experimental and Modeling Investigation of Liquid-Induced Agglomeration in a Gas–Solid Fluidized Bed with Liquid Spray

Experimental Investigation of Bubble and Particle Motion Behaviors in A Gas-Solid Fluidized Bed with Side Wall Liquid Spray

A Volatile Spray Zone Model and Experimentation in a Gas-Solid Fluidized Bed with Liquid Injection

Experimental Investigation of Electrostatic Effect on Particle Motions in Gas-Solid Fluidized Beds

A CFD-DEM study of a two-joint spouting flow pattern in a multiple rectangular spout fluidized bed

Numerical Simulation of Two-Dimensional Spouted Bed with Draft Plates by Discrete Element Method

Influences of operating parameters on the hydrodynamics of a 3-D spout–fluid bed based on DEM modeling approach

Numerical Study of Particle Injection into a Gas-Solid Fluidized Bed

Investigation of fluidization behavior of high density particle in spouted bed using CFD–DEM coupling method

Experimental study on the scale-up of a multi-ring inclined nozzle spout-fluid bed by electrical capacitance tomography

Three-Dimensional Modeling of Gas–Solid Motion in a Slot-Rectangular Spouted Bed with the Parallel Framework of the Computational Fluid Dynamics–Discrete Element Method Coupling Approach

Experimental Study on the Two-Phase Flow Structure in a Supercritical Water-Fluidized Bed

Experimental Investigation on Gas-Solid Hydrodynamics of Coarse Particles in A Two-Dimensional Spouted Bed

An XCT study on three-dimensional characteristics of a spout-fluid bed

Numerical Investigation of the Time-Related Properties of Solid Phase in a 3-D Spout-Fluid Bed

CFD‐DEM Simulation of the Spout–annulus Interaction in a 3D Spouted Bed with a Conical Base

Numerical investigation of gas thermal property in the gasification process of a spouted bed gasifier

Effect of Operating Parameters on Gas‐Solid Hydrodynamics and Heat Transfer in a Spouted Bed

Solids Mixing Intensification in Tapered Fluidized Beds with an Inlet Jet: Experimental Validation and CFD Simulation