Abstract:Spout-fluid beds are widely used in the process industry due to their facilitation of an efficient contact between particles and gas. In this paper, a two-fluid model (TFM) is set up to reproduce the various flow structures encountered during spout-fluid bed operation. The effects of normal restitution model and gas-solid drag model are assessed by comparing simulation results with the experimental and discrete particle modeling (DPM) data of Link et al. [Link et al. Chem. Eng. Sci. 2005, 60, 3425-3442; Link et al. AIChE J. 2008, 54, 1189-1202.]. Simulation results show that application of an effective restitution coefficient in TFM can improve the accuracy of prediction significantly. The drag model of HKL predicts a more reasonable result than models of Huilin-Gidaspow, BVK, and Syamlal and O'Brien. Analysis on relative contributions of kinetic motion, friction, and collision to particle-particle momentum transfer parameters, namely, particle pressure and viscosity, shows that particle-particle momentum transfer in the spout and fountain regions is dominated by kinetic motion and that in the annulus region is dominated by friction. A transition region between spout and annulus regions is proposed. This region can be delineated using a single parameter of dimensionless collisional particle pressure because in this region, particle pressure is dominated by the collisional contribution. With an increasing spout-fluid ratio, the stable spout-annulus-fountain structure gradually shifts to an unstable bubble-slug structure. The effect of collision increases and extends to the entire bed. Meanwhile, the effects of kinetic motion and friction decrease. When slugs are formed, a rebound in the influence of friction is observed, accompanied by a decrease in the influence of collision.

Experimental Investigation on Gas-Solid Hydrodynamics of Coarse Particles in A Two-Dimensional Spouted Bed

Experimental and numerical investigation of solid behavior in a gas–solid turbulent fluidized bed

Experimental Investigation of Bubble and Particle Motion Behaviors in A Gas-Solid Fluidized Bed with Side Wall Liquid Spray

CFD Simulation of Hydrodynamic Characteristics in a Multiple-Spouted Bed

Numerical Simulation of Two-Dimensional Spouted Bed with Draft Plates by Discrete Element Method

Experimental Studies of Particle Flow Dynamics in A Two-Dimensional Spouted Bed

DEM Simulation of the Particle Dynamics in Two-Dimensional Spouted Beds

Three-Dimensional Modeling of Gas–Solid Motion in a Slot-Rectangular Spouted Bed with the Parallel Framework of the Computational Fluid Dynamics–Discrete Element Method Coupling Approach

Flow patterns of solids in a two-dimensional spouted bed with draft plates: PIV measurement and DEM simulations

Influences of operating parameters on the hydrodynamics of a 3-D spout–fluid bed based on DEM modeling approach

Investigation of fluidization behavior of high density particle in spouted bed using CFD–DEM coupling method

Study on the Hydrodynamics of a Spouting−Moving Bed

A CFD-DEM study of a two-joint spouting flow pattern in a multiple rectangular spout fluidized bed

Numerical Investigation of the Time-Related Properties of Solid Phase in a 3-D Spout-Fluid Bed

Two-Fluid Simulation of a Three-Dimensional Spout-Fluid Bed: Flow Structures, Regimes, and Insight into the Mechanism of Particle–Particle Momentum Transfer

Numerical Investigation of the Gas‐Solid Flow Characteristics in a Three‐Dimensional Spouted Bed with a Draft Tube

Hydrodynamic Behavior of a Three‐Phase Spouted Bed with Very Large Particles

Effect of Operating Parameters on Gas‐Solid Hydrodynamics and Heat Transfer in a Spouted Bed

Numerical Simulation of Spouting of Cylindroid Particles in A Spouted Bed

Parallel CFD–DEM Modeling of the Hydrodynamics in a Lab-Scale Double Slot-Rectangular Spouted Bed with a Partition Plate

Particle‐scale Investigation of the Solid Dispersion and Residence Properties in a 3‐D Spout‐fluid Bed