Abstract:Proceedings of the Institution of Mechanical Engineers, Part J: Journal of Engineering Tribology, Ahead of Print. Wear is a significant cause of material loss, contributing to surface degradation of crucial components, notably within engineering sectors. This article is dedicated to enhancing tribological properties through the implementation of Al2O3-based ceramic coatings, specifically targeting situations where reciprocating sliding wear predominates. This study introduces lanthanum oxide (La2O3), a rare earth oxide, as a reinforcing material in Al2O3 coatings in varying weight percentages of 1.2%, 1.6%, and 1.8% respectively along with 3% hexagonal boron nitride (h-BN). The coatings were developed by the high-velocity oxy-fuel (HVOF) surface modification technique, with SS304 serving as the substrate. The porosity, hardness, and chemical composition of the developed coatings were examined. Additionally, reciprocating tribological testing of the coatings was conducted at two loads (5 N and 15 N) under dry sliding conditions. Results indicated that coating containing 95.4% Al2O3–3% h-BN–1.6% La2O3 reduced the porosity up to 50% and improved hardness by 46% compared to the 97% Al2O3–3% h-BN coating. The formation of the α-Al2O3 phase leads to an increase in coating hardness and a reduction in porosity. Notably, the coating comprising 97% Al2O3–3% h-BN exhibited the lowest coefficient of friction among all developed coatings under both loads. Furthermore, an increase in load led to a decrease in the coefficient of friction for all developed coatings. Furthermore, the addition of La2O3 (1.6 wt%) to the coating with 3 wt% h-BN exhibited the lowest wear at both loads. The findings also revealed increased wear at high loads for all developed coatings. SEM, EDS, and XRD analysis of the worn surfaces revealed the contribution of h-BN and La2O3 in enhancing friction behavior through the formation of oxides such as α-Al2O3, B2O3, Al8B2O15, and Al11La0.497O17, along with alterations in wear mechanism and the size of wear debris. The composite coatings developed in this study shall be helpful in advanced engineering applications.

The wear properties of Al-BN nanosheets coating by cold spray

Fabrication and performance of Ni-Co-P/Si3N4 electroplated composite coatings on al-si alloys

Microstructure, Mechanical Properties, and Two-Body Abrasive Wear Behavior of Cold-Sprayed 20 vol.% Cubic BN-NiCrAl Nanocomposite Coating

Cold‐Sprayed Boron‐Nitride‐Nanotube‐Reinforced Aluminum Matrix Composites with Improved Wear Resistance and Radiation Shielding

Enhancing Mechanical and Tribological Properties of Cold-Sprayed Aluminum Through Graphene Nanoplatelet and Boron Carbide Reinforcement

Tribological behaviour of Ag–BN coatings prepared by plasma spraying

Effect of Component Particle Size on Microstructure and Properties of AlSi Coated BN Coatings

Effect of Particle Morphology on Microstructure and Properties of AlSi/BN Coating

Multiple strengthening mechanisms of cold-sprayed cBNp/NiCrAl composite coating

Effect of nano‐Al 2 O 3 on the microstructure and properties of NbB 2 ‐NbC composite coatings prepared by plasma spraying

Effect of h-BN nanoparticles incorporation on the anti-corrosion and anti-wear properties of micro-arc oxidation coatings on 2024 aluminum alloy

Influence of Al2O3 and h-BN on Wear and Corrosion Performance of IN625 Nickel-Based Coating

Tribological Characteristics of Boron Nitride Nanosheets on Silicon Wafers Obtained by the Reaction of MgB2 and NH3

Microstructure and tribological properties of atmospheric plasma-sprayed TiO2 coatings reinforced by boron nitride nanosheets

Synergism of h-BN and La2O3 in improving the tribological performance of Al2O3 coatings

Nano-Composite Coatings with Improved Mechanical Properties and Corrosion Resistance by Thermal Spraying

Effects of Ni-5 wt% Al/Bi2O3 addition and heat treatment on mechanical and tribological properties of atmospheric plasma sprayed Al2O3 coating

Structure and Wear Behavior of AlCrSiN-based Coatings

Effect of Heat Treatment on the Mechanical and Tribological Properties of Dual-Reinforced Cold-Sprayed Al Coatings

Fabrication of In Situ rGO Reinforced Ni-Al Intermetallic Composite Coatings by Low Pressure Cold Spraying with Desired High Temperature Wear Characteristics

Microstructures, Mechanical Properties and Tribological Behaviors of NiAl-based Composite Coatings with Various Addition of Nb