Abstract:The study investigates the effects of graphene nanoplatelets (GNPs) on the tribological properties of aluminum-based nanocomposites, both annealed after extrusion and non-annealed. It also examines the role of nanosized Al4C3 (aluminum carbide), which forms in the annealed Al/GNPs nanocomposite, on the tribological performance of the nanocomposites. The nanocomposites were fabricated using the powder metallurgy method. The microstructure of the composite materials was characterized using SEM, EDS, XRD and TEM techniques. The coefficient of friction (CF) and mass wear of the composites were measured using a pin-on-disk test under dry sliding friction conditions. The results showed that adding GNPs increased the coefficient of friction (CF) of the nanocomposites by up to 44% at 0.1 wt.% GNP, but the CF decreased by 15% at 1.1 wt.% GNP. The optimal concentration of GNPs for minimizing the CF and mass wear of Al-based nanocomposites was 0.1 wt.%. Additionally, the presence of Al4C3 in the annealed Al/GNP nanocomposite had a positive effect on the CF at low GNP concentrations, with a 38% increases at 0.1 wt.% GNP, but this effect diminished as the GNP concentration increased. The study also found that the mass wear of the nanocomposites increased with the GNP concentration, with a 46% increase in the mass wear from 0.1 wt.% GNP to 0.5 wt.% GNP and a 202% increase from 0.1 wt.% GNP to 1.1 wt.% GNP. The presence of Al4C3 also affected the mass wear, with the effect diminishing as the GNP concentration increased. The study observed an increase in the mass wear with the increase in the GNP concentrations, but the mass wear of the annealed Al/GNPs with 1.1 wt.% GNP and Al4C3 was 52% lower than the Al composite with 1.1 wt.%. Overall, this study provides insights into the role of GNPs and Al4C3 on the tribological performance of aluminum-based nanocomposites.

Enhancing Mechanical and Tribological Properties of Cold-Sprayed Aluminum Through Graphene Nanoplatelet and Boron Carbide Reinforcement

Investigating the Effects of Graphene Nanoplatelets and Al4C3 on the Tribological Performance of Aluminum-Based Nanocomposites

A practical approach to fabrication of nano-Al 2 O 3 reinforced MMC coatings by cold spray: Characterization of nanomechanical and tribological performance

Effect of Heat Treatment on the Mechanical and Tribological Properties of Dual-Reinforced Cold-Sprayed Al Coatings

Enhancement of Corrosion Resistance and Tribological Properties of LA43M Mg Alloy by Cold-Sprayed Aluminum Coatings Reinforced with Alumina and Carbon Nanotubes

The wear properties of Al-BN nanosheets coating by cold spray

Synthesis of carbon nanotube reinforced Al matrix composite coatings via cold spray deposition

Microstructure, Mechanical Properties, and Two-Body Abrasive Wear Behavior of Cold-Sprayed 20 vol.% Cubic BN-NiCrAl Nanocomposite Coating

Cold‐Sprayed Boron‐Nitride‐Nanotube‐Reinforced Aluminum Matrix Composites with Improved Wear Resistance and Radiation Shielding

Influence of graphene nanoplates and titanium diboride particulate on wear and interfacial bonding properties of sintered aluminium alloy composites

The Influence of Cold and Detonation Thermal Spraying Processes on the Microstructure and Properties of Al-based Composite Coatings on Mg Alloy

Synthesis and characterization of graphene nanoplatelets reinforced AA7068 matrix nanocomposites produced by liquid metallurgy route

Microstructural Evolution & Mechanical Properties of ZrO2/GNP and B4C/GNP reinforced AA6061 Friction Stir Processed Surface Composites - A Comparative study

Microstructure and Interfacial Bonding Evolution of Cold Spray Deposited Graphene-Reinforced Composite Feedstock on AZ80 Magnesium Substrate

Multiple strengthening mechanisms of cold-sprayed cBNp/NiCrAl composite coating

Effect of Graphene Nanoplatelet Content on Mechanical and Elevated-Temperature Tribological Performance of Self-Lubricating ZE10 Magnesium Alloy Nanocomposites

Effect of B4C and SiC nanoparticle reinforcement on the wear behavior and surface structure of aluminum (Al6063-T6) matrix composite

Enhancing Tribological Performance of Micro-Arc Oxidation Coatings on 6061 Aluminum Alloy with h-BN Incorporation

Synergistic effects of TiC and graphene on the microstructure and tribological properties of Al2024 matrix composites

Preparation of B4Cp/Al Composites via Selective Laser Melting and Their Tribological Properties

Synthesis of Carbon Nanotube Reinforced Al Matrix Composites Via Cold Spray Deposition