Abstract:Recently, extruded polystyrene (XPS) foam has been used as a component of construction materials; therefore, it is important to characterize its mechanical properties, including shear modulus. Despite the importance, it is often difficult to determine the shear modulus accurately by using many of the conventional methods; therefore, it is desirable to establish another method to measure the shear modulus with a high accuracy. Among various methods, torsional vibration test is advantageous because it can be performed easily under the pure shear stress condition in the test sample and both the in-plane and out-of-plane shear moduli can be obtained. However, it is difficult to find any examples performing the torsional vibration tests. In this study, the in-plane and out-of-plane shear moduli of XPS were determined through torsional vibration tests using samples of various widths. In addition, the shear moduli were also determined through flexural vibration tests and compared with those obtained from the torsional vibration tests. In the torsional vibration tests, the anisotropy in these shear moduli became an obstacle, and the in-plane shear modulus determined using a single sample was often dependent on the width/thickness ratio of the sample. In this condition, the coefficient of variation of the in-plane shear modulus value was often close to 10%. However, when using data obtained from the samples with various width/thickness ratios, both the in-plane and out-of-plane shear moduli could be obtained while reducing the abovementioned dependence. Additionally, the coefficients of variation were restricted to those below 2% and 7% for the in-plane and out-of-plane shear moduli, respectively, and these values were obviously lower than those obtained from the flexural vibration tests (approximately 20%). In the proposed method, both the in-plane and out-of-plane shear moduli can be obtained accurately without using any numerical analyses, which are often required in the standardized methods to improve the accuracy. Thus, for accurate measurement of both types of shear moduli of XPS, we recommend performing torsional vibration tests using a range of samples of various width/thickness ratios.

High precision measurement of shear modulus based on Michelson equal thickness interference

Quick and repeatable shear modulus measurement based on torsional resonance and torsional wave propagation using a piezoelectric torsional transducer

Time-multiplexed laser self-mixing sensor for measurement of multiple material elastic moduli

Laser Self-Mixing Sensor for Simultaneous Measurement of Young’s Modulus and Internal Friction (Invited)

A 2D mark shearing technique for characterizing the mechanical properties of material

Off-epicentral measurement of laser-ultrasonic shear-wave velocity and its application to elastic-moduli evaluation

Application of Air-Coupled Ultrasonic Nondestructive Testing in the Measurement of Elastic Modulus of Materials

A Method to Measure Effective Flexural and Transverse Shear Modulus of Composite Structures with Large Aspect Ratio

DETERMINATION OF MECHANICAL BEHAVIOR OF MEMS MATERIALS

Measurement of mechanical properties for MEMS materials

Design and application of a micro-force measuring system based on the principle of torsion balance

Mems/Nems Mechanical Characterization on Different Thin - Film Materials by Scanning along Micro-Machined Cantilevers

A systematic study on linear thermal expansion coefficient of metals based on interferometric measurement with Fresnel bimirror

Measurement of the Flexural Modulus of Chopped Carbon Fiber Tape Reinforced Thermoplastic with Short Beams

An Apparatus for Measuring Mechanical Properties of Microstructures in Tensile Mode

Determination of the Shear Modulus of Orthotropic Thin Sheets With the Anticlastic-Plate-Bending Experiment

Study Of Non-Contact Measurement Of The Thermal Expansion Coefficients Of Materials Based On Laser Feedback Interferometry

Mechanics analysis and simulation of material Brinell hardness measurement

Torsional Vibration Tests of Extruded Polystyrene with Improved Accuracy in Determining the Shear Modulus

Micro-mechanical Characterisation for MEMS Thin Films by Bending Μ-Machined Cantilevers

An integrated push-to-pull micromechanical device: Design, fabrication, and in-situ experiment