Abstract:An ultrasonic vibration-assisted air-cooled stirring rod process (ACSR + UV) was used to efficiently prepare a large-volume semisolid slurry with a mass of more than 40 kg. A low-cost Al–Si–Fe–Mg–Cu–Zn die-casted alloy with high thermal conductivity, high plasticity and medium strength was developed. The alloy was used to manufacture large, thin-walled parts for 5G base stations by using the ACSR + UV rheological die-casting (ACSR + UV R-DC) process. Investigations were performed on the microstructure, porosity, mechanical properties, fracture behaviour and thermal conductivity of the ACSR + UV R-DC alloy, which was then compared to traditionally die-casted (T-DC) and ACSR R-DC alloys. The mechanisms for the microstructural refinement and enhancement of the mechanical and thermal conductivity performances of the ACSR + UV R-DC alloy were also analysed. The results showed that the ACSR + UV process increased the nucleation rate of the melt due to the increase in the nucleation area and the generation of cavitation bubbles. A radial- and an axial-forced convection was also generated inside the melt under the combined effects of acoustic flow and mechanical stirring, thereby homogenising the melt composition field and the temperature field. Therefore, the ACSR + UV R-DC process not only refined the primary α-Al (α1-Al), the eutectic silicon and the secondary α-Al (α2-Al), but also greatly improved the morphology and the distribution of the β-Al5FeSi phase. The mechanical properties of the ACSR + UV R-DC alloy were higher than those of the T-DC and the ACSR R-DC alloys. Compared to the T-DC alloy, the ultimate tensile strength, elongation and yield strength of the ACSR + UV R-DC alloy were increased by 34%, 122% and 19%, respectively. This was because the ACSR + UV R-DC technique gave the alloy the characteristics of high density, fine spherical α1-Al grain and a fine and uniform β-phase, which improved the fracture behaviour of the alloy. The thermal conductivity of the ACSR + UV R-DC alloy was 184 W/(m K), which was 10.2% and 3.4% higher than that of T-DC and ACSR R-DC alloys, respectively. This was because the refined eutectic silicon and β phases in the ACSR + UV R-DC alloy facilitated an easier electron flow through the eutectic region, and the decrease in porosity increased the effective area of heat conduction.

Production and Characterization of Highly Conductive Aluminum Metal for Electric Motor Applications

Influence of Inoculation and Texture on Enhancing Electrical Conductivity in Commercially Pure Aluminum for Squirrel-Cage Asynchronous Electrical Motors

Enhanced Mechanical Strength and Electrical Conductivity of Al–Ni‐Based Conductor Cast Alloys Containing Mg and Si

Development of the manufacturing process of aluminum alloys with high strength and conductance

Study of an active heat dissipating liquid metal wire with electrical‐material co‐transmission characteristics and its applications

Microstructure design to achieve optimal strength, thermal stability, and electrical conductivity of Al-7.5wt.%Y alloy

A review on aluminum alloy conductors influenced by alloying elements and thermomechanical treatments: Microstructure and properties

Hot tearing and mechanical properties of high electrical and thermal conductivity Al-Fe-Mg-Si-Ni Alloys

Alloying Elements Effects on Electrical Conductivity and Mechanical Properties of Newly Fabricated Al Based Alloys Produced by Conventional Casting Process

Synchronously Improving the Thermal Conductivity and Mechanical Properties of Al–Si–Fe–Mg–Cu–Zn Alloy Die Castings Through Ultrasonic-Assisted Rheoforming

Low Resistivity Aluminium Alloy of High Tensile Strength and Elongation

Development of a New Al-Fe-Ni Alloy for Electric Vehicle Applications

Characterization of a Cast Al-Cu Alloy for Automotive Cylinder Head Applications

Characterisation of a High-Performance Al-Zn-Mg-Cu Alloy Designed for Wire Arc Additive Manufacturing

Microstructure and Mechanical Properties of Steel and Ni-Based Superalloy Joints for Rotors of High-Speed Electric Motors

Characterisation of a High-Performance Al–Zn–Mg–Cu Alloy Designed for Wire Arc Additive Manufacturing

Development of Technology for Producing High-Alloyed EIS with Low Specific Magnetic Losses and High Adhesion of Electrical Insulating Coating

Refining Alnico 8 magnets with composition optimization of matrix phase, directional solidification and magnetic field annealing

A novel rheological high pressure die-casting process for preparing large thin-walled Al–Si–Fe–Mg–Sr alloy with high heat conductivity, high plasticity and medium strength

Simultaneous enhancement of coercivity and electric resistivity of Nd-Fe-B magnets by Pr-Tb-Al-Cu synergistic grain boundary diffusion toward high-temperature motor rotors

Processing of an As-Cast Al-7.5 Wt%y Eutectic Alloy by Rolling and Annealing to Improve the Tradeoff Between Strength and Electrical Conductivity