Abstract:The automotive industry is constantly striving for targets for the development of lightweight materials for less fuel consumption and carbon emissions. For this purpose, lighter and higher-performance Al-Si alloys with high service life are preferred in mechanical systems to increase fuel efficiency. However, uncertainties regarding the mechanical and machining properties of these alloys continue in the industrial sector for sustainability in manufacturing. In particular, knowing these properties of Al-Si-Mg alloys used in engine blocks, engine covers, cylinder heads and pistons is important in terms of operating performance and service life in mechanical systems. In this study, Al-7Si-Mg alloy was manufactured by the permanent mould casting (PMC) method and the microstructural, mechanical and machining properties of this alloy in as-cast (ACst) and T6 heat-treated (HTed) states were investigated. Optical microscope (OM) and Scanning Electron Microscope (SEM) imaging processes were used to determine the phases in the microstructure of the alloy. The mechanical properties of the alloy were stated using tensile tests and the Brinell hardness measurement method. Milling tests were applied in the machinability tests, and these tests were realized with TiAlN coated carbide tools on the CNC milling machine using three different cutting speeds- CSs ( V : 50, 80 and 110 m/min), feed rates- FRs ( f : 0.08; 0.16 and 0.24 mm/rev) and constant depth of cut- DoC (1 mm). The microstructure of the ACst alloy consisted of α-Al, primary Si, coral-like eutectic Al-Si, acicular β-Fe (β-Al 5 FeSi) and script-like π-Fe (π-AlSiMgFe) intermetallic phases. After the heat treatment (HT), the present phases in the microstructure partially dissolved and clustered, and these phases coarsened and turned into a spherical morphology. As a result of the HT, the hardness, yield ( YS ) and tensile strength ( TS ) values of the alloy augmented, while the elongation to fracture ( EF ) was reduced. After milling tests, cutting force ( F ), surface roughness ( Ra ), BUL (Built-up layer) and BUE (Built-up edge) values in the ACst and HTed alloys decreased depending on the increase in CS , while they increased with the increase in FR . The results showed that HTed alloys should be subjected to machining operations with a combination of high cutting speed and low feed rate to achieve high mechanical service life and machined surface quality. It was determined that industrial practitioners could increase performance in manufacturing by considering this situation.

Characterization of a Cast Al-Cu Alloy for Automotive Cylinder Head Applications

Effect of Ti on Microstructure and Mechanical Properties of Die-Cast Al-Mg-Zn-Si Alloy

Effect of copper addition on mechanical properties and microstructures of LM25 cast alloys

Evaluation of Two New Cast Aluminum Alloys for High Performance Cylinder Heads

Effects of Cu Addition on the Microstructure and Properties of the Al–Mn–Fe–Si Alloy

Effect of Cooling Rate on the Microstructure and Mechanical Properties of Al-5Cu-0.38Mg-0.32Mn-0.1Ag Alloy Cylinder Heads

Effect of Copper on Tensile and Hardness of Al-Si Alloy in Automotive Application

The Role of Silicon Morphology in the Electrical Conductivity and Mechanical Properties of As-Cast B319 Aluminum Alloy

Effects of Thermal Variables of Solidification on the Microstructure and Hardness of the Manganese Bronze Alloy Cu-24Zn-6Al-4Mn-3Fe

New High Strength and Heat Resistance Aluminum Alloy Material for Engine Cylinder Head

Effect of Zr Addition on Selected Properties and Microstructure of Aluminum Alloy AlSi5Cu2Mg

Enhanced comprehensive performance via alloying and rheo-diecasting in a semi-solid Al–Si–Fe–Mg–Cu–Sr alloy

Homogenization heat treatment influence on microstructure evolution and mechanical properties of as-cast Al-Li-Cu-Mg-Zr alloy for lightweight aerospace application

Mechanical Properties and Conductivity of Low-Pressure Die-Cast 319 Aluminum Prepared with Hot Isostatic Pressing, Thermal Treatment, or Chemical Treatment

Investigations on microstructural, mechanical, and tribological properties of Al-Cu-Ni alloy in cast, heat-treated, and strain-softened conditions

Microstructure and Mechanical Properties of Cast Al-Si-Cu-Mg-Ni-Cr Alloys: Effects of Time and Temperature on Two-Stage Solution Treatment and Ageing

Microstructure, Phase Formation and Heat-Treating of Novel Cast Al-Mg-Zn-Cu-Si Lightweight Complex Concentrated Aluminum Based Alloy

Microstructural, Mechanical, and Tribological Characteristics of Ceramic Reinforced Al/Cu Hybrid Matrix Composites

Alloying Elements Effects on Electrical Conductivity and Mechanical Properties of Newly Fabricated Al Based Alloys Produced by Conventional Casting Process

Experimental Investigations on Microstructure, Mechanical and Wear Behavior Under Dry Sliding of Al6061 with Particulate-Reinforced SiC and TiB2 Metal Matrix Composite Developed by Stir Casting

An Experimental Study on Microstructural, Mechanical and Machinability Properties of As-Cast and Heat-Treated Al-7Si-Mg Alloy