Abstract:Enhancement of thermal stability in Al-Ni alloys through microalloying with slow-diffusing elements, specifically Zr, has been previously reported which is attributed to Zr segregation at the Al/Al 3 Ni interface. In this study, we explore the influence of microalloying Al-Ni alloys with Zr, Ti, V, and Fe on microstructural evolution, hardness, and electrical and thermal conductivity across a range of heat-treatment temperatures from 300 to 450 °C. The distribution of microalloying elements and precipitates after heat treatment is characterized using atom probe tomography (APT). Our investigation confirms Zr segregation to the Al/Al 3 Ni interface, while similar interfacial segregation is absent with the addition of Ti, V, and Fe. Additionally, our analysis of the Al 3 Ni microfiber morphology reveals that their coarsening and spheroidization rates are similar with and without interfacial segregation; thus, retaining the fiber reinforcement through interfacial segregation of slow diffusing elements may not be an effective strategy. Precipitation of L1 2 nanoparticles was found to be the dominant mechanism affecting enhanced hardness and electrical conductivity in Al-Ni-Zr alloys, attributed to precipitation strengthening and solute depletion, respectively. Similar precipitation was not observed for additions of Ti, V, and Fe following heat treatment. We provide a thermodynamic explanation for this limitation. The findings of this study suggest that an effective approach for designing Al-Ni alloys should involve prioritizing microalloying elements to maximize L1 2 precipitation and minimize solute content in the FCC-Al matrix post heat treatment, rather than focusing on Al/Al 3 Ni interfacial segregation.

Hot tearing and mechanical properties of high electrical and thermal conductivity Al-Fe-Mg-Si-Ni Alloys

Enhanced Mechanical Strength and Electrical Conductivity of Al–Ni‐Based Conductor Cast Alloys Containing Mg and Si

Effect of Fe Addition on Microstructure and Properties of Al-3ni Alloys

The Mechanical Properties of Intermetallic Ni50−xTi50Alx Alloys (X=6,7,8,9)

Effect of Ni addition on the microstructure, conductivities and mechanical properties of as-cast Al-Fe alloys

Development of a New Al-Fe-Ni Alloy for Electric Vehicle Applications

Preparation and properties of FeNiMnCuC0.2Alx high-entropy alloy

Effects of Ni Content on Low Cycle Fatigue and Mechanical Properties of Al-12Si-0.9Cu-0.8Mg-xNi at 350 °C

Effect of Silicon Micro-Alloying on the Thermal Conductivity, Mechanical Properties and Rheological Properties of the Al–5Ni Cast Alloy

High Temperature Tensile Deformation Behavior of New Heat Resistant Aluminum Alloy

Alloying Elements Effects on Electrical Conductivity and Mechanical Properties of Newly Fabricated Al Based Alloys Produced by Conventional Casting Process

Effect of microalloying additions on microstructural evolution and thermal stability in cast Al-Ni alloys

Microstructure, Mechanical Properties, and Fatigue Fracture Characteristics of High-Fracture-Resistance Selective Laser Melting Al-Ni-Cu Alloys

Developing High Performance Mechanical Properties at Elevated Temperature in Squeeze Cast Al-Cu-Mn-Fe-Ni Alloys

Microstructure and Mechanical Properties at Elevated Temperature of Mg-Al-Ni Alloys Prepared Through Powder Metallurgy

Effects of Ni content on microstructure and wear behavior of Al–13Si–3Cu–1Mg-xNi-0.6Fe-0.6Mn alloys

The Evolution of Microstructure and Mechanical Properties at Elevated Temperature of Cast Al–Li–Cu–Mg Alloys with Ni Addition

Towards high mechanical performance Al–Cu–Mg–Fe–Ni alloy: influence of composition, solution treatment and aged process on microstructural evolution and mechanical properties

Achieving Low Hot Tearing Susceptibility in High-Strength Cast Al-Li Alloys: Experimental Investigation and Simulation Assessment

Effects of A-EMS on Microstructure and Mechanical Properties of DC Casting Al-10Si-1.1Ni Alloy

Study of the high-temperature mechanical properties of Al-6061/NiTi reinforced metal matrix composites