Abstract:One of the important failure criteria of press operations in industry for forming simulations is the Forming Limit Diagram (FLD). The complex loading effects on FLD, in particular the localized necking phenomenon under stretch-bending condition, have not been fully investigated and well understood. In practical sheet metal applications, the deformation is invariably three dimensional with a combination of stretching and bending. For most sheet materials under these complex loading processes used in industry, strong Bauschinger effect is observed, and the material hardening behavior tends to be anisotropic. This study aims to understand and evaluate such anisotropic hardening effect on the forming limit prediction under stretch-bending condition. The extended through-thickness Marciniak–Kuczynski (M–K) analysis is incorporated with Yoshida–Uemori (YU) two-surface kinematic hardening constitutive model, which has a more accurate description of the reverse loading behavior than that of the conventional isotropic hardening model. The material parameters used in this paper for YU model are calibrated with the experimental data from uniaxial large-strain tension-compression cyclic test. Both the isotropic hardening and YU kinematic hardening models with Hill'48 yield surface are employed in the analysis for the purpose of comparison. The Forming Limit Average Stress Diagram (FLASD) under stretch-bending condition is proposed to extend the understanding of Forming Limit Stress Diagram (FLSD) from in-plane to out-of-plane deformations. The “bending-ratio-dependent” phenomenon in forming limit diagram is predicted and observed in both stress/strain space with the proposed method. It suggests that the individual stress/strain state cannot represent system behavior. Forming limits under stretch-bending is suggested as an occurrence of system instability, not individual material instability. The system behavior of sheet metal deformation is reinforced as critical to the understanding of necking instability in stretch bending processes. The analysis shows that the Bauschinger effect provides positive effect in delaying the necking instability, predicting higher formability for sheet metals under stretch-bending. The insight obtained in this paper provides further understanding of the localized necking phenomenon under stretch-bending condition.

Formability of SS304 stainless steel foil at elevated strain-rate

Variation In Mechanical Properties, Microstructures And Fracture Behavior Of 304 Stainless Steel During Low-Cycle Fatigue

M–K Ductile Damage Theory Predicts Formability of Stainless Steel Ultra-Thin Strips in Stamping

Feasibility evaluation of failure models for predicting forming limit of metal foils

Formability and Mechanism of Ultra-Thin Titanium Foil under the Elevated Temperature and High Strain Rate in Electromagnetic Forming

Investigation on formability of bipolar plates during flexible micro forming of Cu/Ni clad foils

Failure and forming quality study of metallic foil blanking with different punch-die clearances

Effect of Strain Rate on the Mechanical Properties of Cu/Ni Clad Foils

An Experimental and Simulation Study on the Formability of Commercial Pure Titanium Foil

Specimen Dimension and Grain Size Effects on Deformation Behavior in Micro Tensile of Sus304 Stainless Steel Foil

Formability Analysis of Electrically Assisted Double-Side Multi-Point Incremental Sheet Forming

Experimental Investigation on Forming Limits of AA5052 Sheet in Hybrid Quasi-Static/dynamic Plane-Strain Tensile Process

Quasi-static-dynamic Formability of AA5052-O Sheet under Uniaxial and Plane-Strain Tension

Evaluation of the Forming Limit of Incremental Sheet Forming Based on Ductile Damage

The Experimental and Numerical Investigation on the Mechanical Properties of Metallic Foil

Sheet metal forming limits under stretch-bending with anisotropic hardening

Local formability of medium-Mn steel

Fracture behavior of 7075-T6 aluminum alloy under electromagnetic forming and traditional stamping

Investigation of Size Effects of 304 Stainless Steel Foils in Microforming Processes

Experimental Observations of Quasi-Static-Dynamic Formability in Biaxially Strained Aa5052-O

Investigations on the Forming Characteristics of a Novel Flexible Incremental Sheet Forming Method for Low-Ductility Metals at Room Temperature