Abstract:The second-generation high-temperature superconducting (2 G-HTS) tapes are subjected to complex stress/strain in practical applications. For the complex operation conditions, lamination techniques are widely used to improve the robustness of 2 G-HTS tapes. However, lamination makes the 2 G-HTS tape structure more complicated, which can significantly affect their electro-mechanical behaviors. In this work, uniaxial monotonic tensile tests were performed to obtain the stress-strain relationship and the strain dependence of critical current ( I c ( ε )) in liquid nitrogen conditions. Two types of laminated 2 G-HTS tapes (copper-laminated and stainless steel-laminated) were compared with copper-plated 2 G-HTS tapes. The results showed that the irreversible tensile strains of Cu-laminated and SS-laminated tapes were much higher than that of Cu-plated tapes, which increased by ∼35 % and ∼60 %, respectively. High consistency between the experimental and theoretical I c values in 2 G-HTS tapes under tensile strain was verified by the I c ( ε ) model. Based on the residual strain ( ε res ) calculation of composite multilayer structures, we confirmed that it was mainly due to the increase of the compressive residual strain of superconducting layers. Further, tensile fatigue tests also confirmed the significant improvement of the tensile fatigue electro-mechanical behaviors in the laminated 2 G-HTS tapes. Finally, 2D X-ray and SEM cooperative analysis were used to characterize the tape microstructure before and after fatigue, and the correlation between micro-defects and non-destructive imaging features was established. It was found that the internal solder layer and its interface were seriously damaged to release the stress. This work provides a strategy to improve the electro-mechanical behaviors of 2 G-HTS tapes by adjusting the composite structure to change residual strain.

Determination of Internal Strain and Residual Stress in Wires HTSC-2 Using Neutron Stress Diffractometry

Internal Strain Measurement by Neutron Diffraction Under Transverse Compressive Stress for Nb 3 Sn Wires With and Without Cu-Nb Reinforcement

Strain analysis by neutron diffraction on Nb3Sn strands in ITER central solenoid conductors of short and long twist pitch

Determination of the electromechanical limits of high-performance Nb$_3$Sn Rutherford cables under transverse stress from a single-wire experiment

Novel Two-Step Procedure for Measuring I C Vs. Tensile Stress of Commercial REBCO Tape

Stress dependence of the critical currents in neutron irradiated (RE)BCO coated conductors

Axial Tensile Stress-Strain Characterization Of Bi-2212 Round Wire With Different Heat Treatments

Experimental Studies of Critical Currents and Joint Resistance of HTS Twisted Stack Slotted-Core Cables

A new enclosed method for transverse mechanical testing on CICC conductors

Deformation Behavior and Degradation on Rutherford Cabling of Nb 3 Sn Wires

Experimental verification of the temperature and strain dependence of the critical properties in Nb/sub 3/Sn wires

Metallographic Investigation of First Full-Size High-Jc Nb3Sn Cable-in-conduit Conductor after Cyclic Loading Tests

Structural Design and Mechanical Analysis of HTS CICC Made From Twisted Stack Slotted-Core Cable

Neutron diffraction methods for the study of residual stress fields

Determination of I-V Curves of HTS Tapes From The Frequency Dependent AC Transport Loss

Critical Current under Uniaxial Strain on High-Pressure Heat Treatment Bi-2212 Round Wire

Conceptual Design of an HTS Dipole Insert Based on Bi2212 Rutherford Cable

Nb3Sn wire shape and cross sectional area inhomogeneity in Rutherford cables

Enhancement mechanism of uniaxial tensile electro-mechanical behaviors in second-generation high-temperature superconducting tapes

Advances in XRD Characterization of 2G HTS Wire for Low-Temperature Magnet Applications

Research on Mechanical Properties of High-Performance Cable-in-conduit Conductors with Different Design