Abstract:The combination of wire arc additive manufacturing (WAAM) technology with traditional manufacturing process provides a promising method for fabricating the large and complex parts with the advantages of high performance, time-saving, low cost and high material utilization. In order to acquire the optimal hybrid manufacturing process, the comparative study of flow behaviors and microstructure evolution of wrought and WAAMed ultrahigh-strength (UHS) steels is carried out under the temperatures of 920–1160 oCdocumentclass[12pt]{minimal}usepackage{amsmath}usepackage{wasysym}usepackage{amsfonts}usepackage{amssymb}usepackage{amsbsy}usepackage{mathrsfs}usepackage{upgreek}setlength{oddsidemargin}{-69pt}egin{document}$${}^{{ ext{o}}}{ ext{C}}$$end{document} and strain rates of 0.01–10 s-1documentclass[12pt]{minimal}usepackage{amsmath}usepackage{wasysym}usepackage{amsfonts}usepackage{amssymb}usepackage{amsbsy}usepackage{mathrsfs}usepackage{upgreek}setlength{oddsidemargin}{-69pt}egin{document}$${ ext{s}}^{{ - 1}}$$end{document}. The results show that the coarse prior austenite columnar grains and carbides in the initial microstructure of the WAAMed UHS steel contribute to the higher flow stress and slower dynamic recrystallization (DRX) kinetics during hot deformation as compared to the wrought UHS steel. The hot activation energy under the peak stress of the wrought and WAAMed UHS steels is estimated to be 332.3 kJ/mol and 374.1 kJ/mol, respectively. On the basis of the hot processing maps, the common optimal processing window for WAAMed and wrought UHS steels is determined as the temperatures of 1060–1160 oCdocumentclass[12pt]{minimal}usepackage{amsmath}usepackage{wasysym}usepackage{amsfonts}usepackage{amssymb}usepackage{amsbsy}usepackage{mathrsfs}usepackage{upgreek}setlength{oddsidemargin}{-69pt}egin{document}$${}^{{ ext{o}}}{ ext{C}}$$end{document} and strain rates of 0.08–0.66 s-1documentclass[12pt]{minimal}usepackage{amsmath}usepackage{wasysym}usepackage{amsfonts}usepackage{amssymb}usepackage{amsbsy}usepackage{mathrsfs}usepackage{upgreek}setlength{oddsidemargin}{-69pt}egin{document}$${ ext{s}}^{{ - 1}}$$end{document}. Under these deformation parameters, the microstructures of WAAMed and wrought UHS steels consist of fine DRXed grains, and the DRX behaviors are both dominated by the discontinuous DRX and continuous DRX mechanisms.Graphical Abstract

Hot deformation induced microstructural evolution in local-heterogeneous wire + arc additive manufactured 2219 Al alloy

Enhanced High-Temperature Strength and Ductility of Wire Arc Additive Manufactured Al-Ce-Mg Alloys with Fine Α-Al/al11ce3 Eutectics

Influence of temperature on deformation and damage mechanisms of wire + arc additively manufactured 2219 aluminum alloy

Microstructure evolution and mechanical properties of the wire + arc additive manufacturing Al-Cu alloy

Mechanical properties and precipitation behavior of the heat-treated wire + arc additively manufactured 2219 aluminum alloy

The heterogeneous band microstructure and mechanical performance in a wire + arc additively manufactured 2219 Al alloy

Microstructure and mechanical properties of wire arc additively manufactured 205A high strength aluminum alloy: The comparison of as-deposited and T6 heat-treated samples

Hot Deformation Behavior and Microstructure Evolution of High-Strength Al-Zn-Mg-Cu Alloy

Microstructure and mechanical properties of wire arc additive manufactured ZL205A alloy

Achieving high strength-ductility of Al-Zn-Mg-Cu alloys via hot-wire arc additive manufacturing enabled by strengthening precipitates

Minimizing porosity and optimizing microstructure of hot-wire arc additive manufactured Al-Cu-Mg-Ag alloy for strength increment

Microstructure Evolution and Performance of AA2024 Alloy Through Wire-Arc Additive Manufacturing Under Different Heat Inputs

Comparative Study of Wire Arc Additive Manufactured and Wrought Ultrahigh-Strength Steels: Flow Behavior and Microstructure Evolution

Improved material properties of wire arc additively manufactured Al-Zn-mg-cu alloy through severe deformation interlayer friction stir processing and post-deposition heat treatment

Hot Workability and Microstructure Evolution of Homogenized 2050 Al-Cu-Li Alloy during Hot Deformation

Microstructure evolution and mechanical properties of wire-arc-additively manufactured Al–Cu–Mg–Ag alloy

Microstructural and mechanical properties of wire-arc additively manufactured Al–Zn–Mg aluminum alloy: The comparison of as-deposited and heat-treated samples

Influence of travel speed on microstructure and mechanical properties of wire + arc additively manufactured 2219 aluminum alloy

Hot Deformation Behavior and Microstructure Evolution of Al-7.92 Zn-1.64 Mg-2.00 Cu Alloy

Improving mechanical properties of wire arc additively manufactured AA2196 Al–Li alloy by controlling solidification defects

Effect of thermal history on microstructure evolution and mechanical properties in wire arc additive manufacturing of HSLA steel functionally graded components