Abstract:The combination of wire arc additive manufacturing (WAAM) technology with traditional manufacturing process provides a promising method for fabricating the large and complex parts with the advantages of high performance, time-saving, low cost and high material utilization. In order to acquire the optimal hybrid manufacturing process, the comparative study of flow behaviors and microstructure evolution of wrought and WAAMed ultrahigh-strength (UHS) steels is carried out under the temperatures of 920–1160 oCdocumentclass[12pt]{minimal}usepackage{amsmath}usepackage{wasysym}usepackage{amsfonts}usepackage{amssymb}usepackage{amsbsy}usepackage{mathrsfs}usepackage{upgreek}setlength{oddsidemargin}{-69pt}egin{document}$${}^{{ ext{o}}}{ ext{C}}$$end{document} and strain rates of 0.01–10 s-1documentclass[12pt]{minimal}usepackage{amsmath}usepackage{wasysym}usepackage{amsfonts}usepackage{amssymb}usepackage{amsbsy}usepackage{mathrsfs}usepackage{upgreek}setlength{oddsidemargin}{-69pt}egin{document}$${ ext{s}}^{{ - 1}}$$end{document}. The results show that the coarse prior austenite columnar grains and carbides in the initial microstructure of the WAAMed UHS steel contribute to the higher flow stress and slower dynamic recrystallization (DRX) kinetics during hot deformation as compared to the wrought UHS steel. The hot activation energy under the peak stress of the wrought and WAAMed UHS steels is estimated to be 332.3 kJ/mol and 374.1 kJ/mol, respectively. On the basis of the hot processing maps, the common optimal processing window for WAAMed and wrought UHS steels is determined as the temperatures of 1060–1160 oCdocumentclass[12pt]{minimal}usepackage{amsmath}usepackage{wasysym}usepackage{amsfonts}usepackage{amssymb}usepackage{amsbsy}usepackage{mathrsfs}usepackage{upgreek}setlength{oddsidemargin}{-69pt}egin{document}$${}^{{ ext{o}}}{ ext{C}}$$end{document} and strain rates of 0.08–0.66 s-1documentclass[12pt]{minimal}usepackage{amsmath}usepackage{wasysym}usepackage{amsfonts}usepackage{amssymb}usepackage{amsbsy}usepackage{mathrsfs}usepackage{upgreek}setlength{oddsidemargin}{-69pt}egin{document}$${ ext{s}}^{{ - 1}}$$end{document}. Under these deformation parameters, the microstructures of WAAMed and wrought UHS steels consist of fine DRXed grains, and the DRX behaviors are both dominated by the discontinuous DRX and continuous DRX mechanisms.Graphical Abstract

Effect of thermal history on microstructure evolution and mechanical properties in wire arc additive manufacturing of HSLA steel functionally graded components

Mechanical Properties, Microstructural Characteristics and Heat Treatment Effects of WAAM Stainless-Steel Plate Material

Microstructure and Mechanical Properties of High-Strength, Low-Alloy Steel Thin-Wall Fabricated with Wire and Arc Additive Manufacturing

Comparison of microstructural characteristics and mechanical properties of the high-strength low-alloy steels fabricated by wire arc additive manufacturing versus conventional casting

Microstructure evolution and mechanical properties of the wire + arc additive manufacturing Al-Cu alloy

Comparative Study of Wire Arc Additive Manufactured and Wrought Ultrahigh-Strength Steels: Flow Behavior and Microstructure Evolution

Microstructure and Mechanical Properties of Low-Carbon High-Strength Steel Fabricated by Wire and Arc Additive Manufacturing

Enhancing Mechanical Properties: Exploring the Effect of Annealing Temperature on Wire Arc Additively Manufactured High-Strength Steel

Wire arc additive manufacturing of high-strength low alloy steels: study of process parameters and their influence on the bead geometry and mechanical characteristics

Mechanical properties and microstructure characteristics of wire arc additively manufactured high-strength steels

Effect of welding parameters on microstructure and mechanical properties of mild steel components produced by WAAM

Effect of heat treatment on the microstructure and mechanical properties of Mg-Gd-Y-Zr alloys fabricated by wire arc additive manufacturing

Mechanical properties of wire and arc additively manufactured high-strength steel structures

Microstructure and Mechanical Properties of AlSi7Mg0.6 Aluminum Alloy Fabricated by Wire and Arc Additive Manufacturing Based on Cold Metal Transfer (WAAM-CMT)

Microstructure Evolution and Performance of AA2024 Alloy Through Wire-Arc Additive Manufacturing Under Different Heat Inputs

Microstructure, Mechanical Properties, and Galvanic Corrosion of 10CrNi3MoV Fabricated by Wire Arc Additive Manufacturing

Microstructural and Defect Evolution during WAAM Resulting in Mechanical Property Differences for AA5356 Component

Characterization of a low-alloy steel component produced with wire arc additive manufacturing process using metal-cored wire

The Effect of Thermal History on Microstructural Evolution, Cold-Work Refinement and α/\b{eta} Growth in Ti-6Al-4V Wire + Arc AM

Microstructure Evolution of Wire-Arc Additively Manufactured 2319 Aluminum Alloy with Interlayer Hammering

Heterogeneous microstructure and anisotropic mechanical properties of reduced activation ferritic/martensitic steel fabricated by wire arc additive manufacturing