Abstract:A collective surface of LiCoO2 is constructed through an interdiffusion reaction of MgHPO4·3H2O. The collective surface renders a three‐layer configuration that demonstrates an amorphous Li3PO4 outmost layer, a spinel‐like layer beneath, and a Mg diffusion layer within LiCoO2 bulk. Consequently, such modified LiCoO2 exhibits ultralong life with capacity retention of 82% after 1000 cycles within 3.0–4.6 V. Rapidly increasing demand for energy density in consumer electronics is eager for developing high‐voltage LiCoO2 (LCO). However, some great challenges such as severe phase transition and surface instability negate the cycle life of LCO operated at high‐voltages (≥4.6 V). Herein, a chemical reconstruction strategy is proposed to form a collective surface of LCO through an interdiffusion reaction of MgHPO4·3H2O (MP) so as to extend the cycle life of high‐voltage LCO. The collective surface renders a three‐layer configuration that demonstrates an amorphous Li3PO4 outmost layer, a spinel‐like layer beneath, and a Mg diffusion layer within LCO bulk. MP with relatively low hardness enables the uniform precoating via mechanical mixing, followed by a sintering process to undergo an interdiffusion reaction. Li3PO4 is an intrinsic electrochemical stabilizer against interfacial side reactions. The spinel‐like compounds build a high‐voltage‐stable surface against irreversible O2 release. In addition, Mg diffuses into the bulk lattice to suppress irreversible phase transition during the deep delithiation of LCO. Therefore, such modified LCO with a collective surface exhibits ultralong life with capacity retention of 82% after 1000 cycles at 1 C within 3.0–4.6 V and stable operating at 4.7 V or elevated temperature (45 °C).

One-Step Sintering Synthesis Achieving Multiple Structure Modulations for High-Voltage LiCoO<sub>2</sub>

One‐Step Sintering Synthesis Achieving Multiple Structure Modulations for High‐Voltage LiCoO2

Structural Evolution of Mg-Doped Single-Crystal LiCoO2 Cathodes: Importance of Morphology and Mg-Doping Sites

Structure/Interface Coupling Effect for High‐Voltage LiCoO2 Cathodes

Structure/Interface Coupling Effect for High‐Voltage LiCoO<sub>2</sub> Cathodes

Structure/Interface Coupling Effect for High‐Voltage LiCoO2 Cathode

Long‐Term Highly Stable High‐Voltage LiCoO2 Synthesized via a Solid Sulfur‐Assisted One‐Pot Approach

Improving Stability of High Voltage LiCoO2 by Synergetic Surface Modification Via in Situ Surface Conversion

Achieving structural stability of LiCoO2 at high-voltage by gadolinium decoration

LiMgPO<sub>4</sub>-Coating-Induced Phosphate Shell and Bulk Mg-Doping Enables Stable Ultra-High-Voltage Cycling of LiCoO<sub>2</sub> Cathode

From Metal to Cathode Material: in situ Formation of LiCoO2 with Enhanced Cycling Performance and Suppressed Phase Transition

Improving diffusion kinetics and phase stability of LiCoO2 via surface modification at elevated voltage

Simultaneous Near‐Surface Trace Doping and Surface Modifications by Gas–Solid Reactions during One‐Pot Synthesis Enable Stable High‐Voltage Performance of LiCoO2

Multiple Surface Optimizations for a Highly Durable LiCoO2 beyond 4.6 V

Multiple Surface Optimizations for a Highly Durable LiCoO<sub>2</sub> beyond 4.6 V

Collective Surface Enabling an Ultralong Life of LiCoO2 at High Voltage and Elevated Temperature

An in Situ Formed Surface Coating Layer Enabling LiCoO2 with Stable 4.6 V High‐Voltage Cycle Performances

Surface Design with Cation and Anion Dual Gradient Stabilizes High-Voltage LiCoO<sub>2</sub>

A multifunctional manipulation to stabilize oxygen redox and phase transition in 4.6 V high-voltage LiCoO2 with sXAS and EPR studies

Unraveling the Distinct Roles of Mg Occupation on Li or Co Sites on High-Voltage LiCoO 2

Multi-scale stabilization of high-voltage LiCoO2 enabled by nanoscale solid electrolyte coating