Abstract:Ni-rich LiNixMnyCo1-x-yO2 (NMC, x ≥ 0.5) cathode materials have attracted intensive attention in developing high energy-density lithium ion batteries, owing to their high capacity and relatively low cost. Among them, LiNi0.8Mn0.1Co0.1O2 (NMC811) is one of the most promising candidates to realize higher energy density, particularly operating at high cut-off voltage (e.g. 4.5 V vs. Li/Li+). However, the limited cycle life is becoming the plague for its practical application due to the structural instability, microcracks formation, and electrolyte decomposition at the electrode/electrolyte interface.[1,2] As well known, single crystal NMC materials have more stable surface activity because of the low surface area and better mechanical stability than conventional polycrystalline materials. Moreover, single crystalline NMC materials can provide not only high gravimetric energy density, but also high volumetric energy density due to the increased tap density compared to the conventional polycrystalline NMC materials.[2-4]In this study, a single crystalline NMC811 sample with a large particle size of around 5 μm and polyhedral shape was synthesized by sol-gel method. Furthermore, a homogeneous ultrathin surface coating layer (~2 nm) was built on the surface of the single crystalline NMC811 particles to act as protective layer to prevent the direct contact between electrolyte and active particles. As a result, the coating layer effectively enhances an overall electrochemical performance of single crystalline NMC811 materials and especially leads to a higher reversible capacity as well as a remarkable improvement of the capacity retention (90% after 200 cycles between 3 and 4.5 V vs. Li/Li+). The influences of the coating layer on the structure and interfacial stability and electrochemical properties will be presented in details later. References: [1] H. Y. Li, J. Li, X. W. Ma.J. R. Dahn. J. Electrochem. Soc. 2018, 165, A1038-A1045. [2] J. Kim, H. Lee, H. Cha, M. Yoon, M. Park, J. Cho. Adv. Energy Mater. 2018, 8, 1702028. [3] H. D. Liu, R. Kloepsch, J. Wang, M. Winter.J. Li. J. Power Sources 2015, 300, 430-437. [4] H. D. Liu, J. Wang, X. F. Zhang, D. Zhou, X. Qi, B. Qiu, J. H. Fang, R. Kloepsch, G. Schumacher, Z. P. Liu et al. ACS Appl. Mater. Interfaces 2016, 8 (7), 4661-4675. Figure 1

Ultra-high rate performance of single-crystalline NMC cathodes enabled by a TEP-based electrolyte

Improving interfacial stability of ultrahigh-voltage lithium metal batteries with single-crystal Ni-rich cathode via a multifunctional additive strategy

Tailoring electrolyte to enable high-rate and super-stable Ni-rich NCM cathode materials for Li-ion batteries

Tuning the Interface Stability of Nickel-Rich NCM Cathode Against Aggressive Structural Collapse via the Synergistic Effect of Additives

Revolutionizing multifunctional electrolyte additive design and synthesis for high-voltage nickel-rich batteries in diverse climates

Effect of Fluoroethylene Carbonate Electrolyte Additives on the Electrochemical Performance of Nickel-Rich NCM Ternary Cathodes

Regulation of Interface Ion Transport by Electron Ionic Conductor Construction toward High‐Voltage and High‐Rate LiNi0.5Co0.2Mn0.3O2 Cathodes in Lithium Ion Battery

Challenges and approaches of single crystal Ni-rich layered cathodes in lithium batteries

High Voltage Operation of Ni‐Rich NMC Cathodes Enabled by Stable Electrode/Electrolyte Interphases

Synthesis of Single Crystalline Ni-Rich NMC811 Cathode Materials and Improved Performance Enabled By Ultrathin Surface Coating Layer

Tuning the End Alkyl Chain of the Ether Solvent to Stabilize the Electrode/Electrolyte Interfaces in the NCM-Li Battery

A short process and low-cost preparation of single crystal LiNi0.6Co0.2Mn0.2O2 cathode for lithium-ion batteries

Boosting the cycling and storage performance of lithium nickel manganese cobalt oxide-based high-rate batteries through cathode manipulation

Enhanced Cycling Performance of Ni-Rich Positive Electrodes (NMC) in Li-Ion Batteries by Reducing Electrolyte Free-Solvent Activity

Enabling stable and high-rate cycling of a Ni-rich layered oxide cathode for lithium-ion batteries by modification with an artificial Li<SUP>+</SUP>-conducting cathode-electrolyte interphase

Self-repaired Cathode Electrolyte Interphase to Stabilize the High-Nickel Cathode Interface by a Sustained-Release Multifunctional Electrolyte Additive

Nonsacrificial Nitrile Additive for Armoring High-Voltage LiNi0.83 Co0.07 Mn0.1 O2 Cathode with Reliable Electrode-Electrolyte Interface toward Durable Battery.

Enabling Structure/Interface Regulation for High Performance Ni‐Rich Cathodes

High-Efficiency Electrolyte for Li-Rich Cathode Materials Achieving Enhanced Cycle Stability and Suppressed Voltage Fading Capable of Practical Applications on a Li-Ion Battery

Stabilizing high-Ni cathodes with gradient surface Ti-enrichment

Multipoint adsorption constructs stable interface chemistry for high-nickel cathode material