Abstract:Fringe patterns are typically produced as the results of traditional optical Nondestructive Evaluation (NDE) employing digital shearography. Structural flaws affect the response of the surrounding material to a certain loading, resulting in unique fringe patterns that are related to the local deformation. Smaller defect information, however, can be easily lost in the fringe pattern caused by global deformation during the flaw detection procedure. In order to improve the flaw detection capabilities of this technology, it is important to streamline the inspection process and to simplify the interpretation of the results. This study proposes a practical and effective methodology that experimentally removes fringe patterns caused by global deformation in digital shearography and only retains the defect information. For shearographic Non-Destructive Testing (NDT), two sets (3 or 4 images) of temporal phase-shifted interferograms under different loads P 1 and P 2 are recorded. This novel approach involves recording one additional set of temporal phase-shifted interferograms at a load between P 1 and P 2 , e.g. P 1' . Two phase maps of shearograms can be generated using the phase shift technique, corresponding to the two loads Δ 2 = (P 1' -P 1 ) and Δ 1 = (P 2 -P 1 ), respectively. Because of the nondestructive nature of the testing, the magnitude of the loads P 1 and P 2 is small, and the 1st derivative of global deformation in the shearing direction of the test part is assumed to be linear. Therefore, a linear coefficient C based on the two shearograms can be determined. The information from global deformation is then removed by subtracting the shearogram generated with the small load Δ 2 multiplied by the correlation coefficient C from the one obtained with the relatively large load Δ 1 . This technique is further improved by calculating a complete surface linear coefficient C ij , which improves the detail processing of the deformation of samples with complex geometry and mechanical properties. This technique is shown to effectively assess a wide range of structures, including aluminum specimens with prepared flaws and intricate composite laminates. The experimental findings demonstrate that the suggested technique improves the non-destructive testing capabilities of digital shearography, thereby simplifying defect detection and visualization.

Non-Destructive Testing Study of Hydrogen Storage COPVs Based on Digital Shearography Technique

Mechanical Analysis of Carbon Fiber Filament Wound Hydrogen Storage Vessel with Aluminum Alloy Liner

Fatigue Test of Carbon Epoxy Composite High Pressure Hydrogen Storage Vessel under Hydrogen Environment

Research on Hydrogen Environment Fatigue Test System and Correlative Fatigue Test of Hydrogen Storage Vessel

Structural health monitoring of hydrogen pressure vessels using distributed fiber optic sensing

Radial Displacement Measurement of Hydrogen Storage Cylinders under Internal Pressure Based on Fringe Projection Profilometry

Experimental and Numerical Investigation of Radial Displacement of COPV Using CT and FPP Method

Experimental Analysis on Residual Performance of Used 70 MPa Type IV Composite Pressure Vessels

A Novel Modeling and Virtual Testing Method of Hydrogen Storage COPV Considering Stochastic Wrinkle Defects

Damage Detection And Leakage Alert Of Fiber Composite Wrapped Tank For High Pressure Hydrogen Storage

Inspection of defects in composite structures using long pulse thermography and shearography

Measurement of Aluminum Liner Internal Defect Deformation and Strain Using Shearography and FEM Verification

Application of deep learning for structural health monitoring of a composite overwrapped pressure vessel undergoing cyclic loading

Quantitative Detection of the Defects in Thin-Walled Pressure Vessels with Holography and Shearing Speckle Interferometry

Micromechanics-based Burst Failure Analysis of Composite Vessel Used for Hydrogen Storage

Robust instrumentation of composite pressure vessels manufactured via multi-filament winding for distributed fiber optic sensing

Detection of Void and Crack Defects in Type IV Hydrogen Storage Vessels by Microwave Technique

Digital shearography for NDT: Study on a novel experiment based method for removing global deformation ✰

Non-destructive testing and structural health monitoring technologies for carbon fiber reinforced polymers: a review

Identifying Void and Crack Defects in Type III Hydrogen Storage Vessels Based on Microwave Inspection

Non-destructive Testing Method for Composite Insulators Based on Digital Shearography