Abstract:Fringe patterns are typically produced as the results of traditional optical Nondestructive Evaluation (NDE) employing digital shearography. Structural flaws affect the response of the surrounding material to a certain loading, resulting in unique fringe patterns that are related to the local deformation. Smaller defect information, however, can be easily lost in the fringe pattern caused by global deformation during the flaw detection procedure. In order to improve the flaw detection capabilities of this technology, it is important to streamline the inspection process and to simplify the interpretation of the results. This study proposes a practical and effective methodology that experimentally removes fringe patterns caused by global deformation in digital shearography and only retains the defect information. For shearographic Non-Destructive Testing (NDT), two sets (3 or 4 images) of temporal phase-shifted interferograms under different loads P 1 and P 2 are recorded. This novel approach involves recording one additional set of temporal phase-shifted interferograms at a load between P 1 and P 2 , e.g. P 1' . Two phase maps of shearograms can be generated using the phase shift technique, corresponding to the two loads Δ 2 = (P 1' -P 1 ) and Δ 1 = (P 2 -P 1 ), respectively. Because of the nondestructive nature of the testing, the magnitude of the loads P 1 and P 2 is small, and the 1st derivative of global deformation in the shearing direction of the test part is assumed to be linear. Therefore, a linear coefficient C based on the two shearograms can be determined. The information from global deformation is then removed by subtracting the shearogram generated with the small load Δ 2 multiplied by the correlation coefficient C from the one obtained with the relatively large load Δ 1 . This technique is further improved by calculating a complete surface linear coefficient C ij , which improves the detail processing of the deformation of samples with complex geometry and mechanical properties. This technique is shown to effectively assess a wide range of structures, including aluminum specimens with prepared flaws and intricate composite laminates. The experimental findings demonstrate that the suggested technique improves the non-destructive testing capabilities of digital shearography, thereby simplifying defect detection and visualization.

Quantitative Detection of the Defects in Thin-Walled Pressure Vessels with Holography and Shearing Speckle Interferometry

Ultrasonic Guided Wave-Based Circumferential Scanning of Plates Using a Synthetic Aperture Focusing Technique

Scattering of Torsional Flexural Guided Waves from Circular Holes and Crack-Like Defects in Hollow Cylinders

Non-Destructive Testing Study of Hydrogen Storage COPVs Based on Digital Shearography Technique

Numerical Analysis of the Measuring Errors in Quantitative Detection of Defects with Shearing Speckle Pattern Interferometry

Quantifying Hidden Defect In Multi-Layered Structures By Using Eddy Current System Combined With A Scanner

Error Analysis of Spherical Scanning Mechanism Used for Surface Defects Detection

Quantitative Analysis on Parameters of a Defect with Speckle Interferometry and Finite Element Optimization Method

On-site detection of seam weld defects by using electronic speckle pattern interferometry

Quantitative Analysis of Defect Parameters by Shearing Speckle Interferometry and Finite Element Optimization Method

A New Nondestructive Technique for Measuring Pressure in Vessels by Surface Waves

Width and Depth Gauging of Rectangular Subsurface Defects Based on All-Optical Laser-Ultrasonic Technology

Deconvolution Imaging of Weak Reflective Pipe Defects Using Guided-Wave Signals Captured by a Scanning Receiver

Imaging of Nonaxisymmetric Area Discontinuities in Pipes Using Guided Wave Synthetic Focusing

A Defects Detection Method of Buried Liquid-Filled Pipes Based on T(0,1) Guided Waves

Digital shearography for NDT: Study on a novel experiment based method for removing global deformation ✰

Multi-time Lamb waves space wavenumber imaging method based on ultrasonic-guided wavefield

Inspection of defects in composite structures using long pulse thermography and shearography

Detection of Small Cracks and Cavities Using Laser Diffraction

Circumferential Ultrasonic Testing for Ultra- High Pressure Vessels and Pipes(1)

Circumferential Ultrasonic Testing for Ultra-high Pressure Vessels and Pipes(2)