Abstract:A cone crusher is a crushing machine which is widely used in the mining, construction and recycling industries. Previous research studies have proposed empirical mathematical models to simulate the operational performance of a cone crusher. These models attempt to match the size distributions of the feed and product streams. The flow of the rock and its breakage within the cone crusher chamber are not explicitly modelled by these methods. Moreover, the ability to investigate the changes in crusher performance affected by changes to the crusher design geometry and/or operating variables (including cavity profile, closed size setting and eccentric speed) are not easily achieved. Improvements to system design and performance are normally achieved by the combination of iterative modifications made to the design and manufacture of a series of prototype machines, and from a subsequent analysis of the results obtained from expensive and time consuming rock testing programs. The discrete element method (DEM) has in recent years proved to be a powerful tool in the execution of fundamental research to investigate the behaviour of granular material flow and rock breakage. Consequently, DEM models may provide the computational means to simulate the flow and breakage of rock as it passes through a cone crusher chamber. Thus, the development of field validated models may provide a cost effective tool to predict the changes in crusher performance that may be produced by incremental changes made to the dimensions or power delivered to the crusher chamber. To obtain an improved understanding of the fundamental mechanisms that take place within a cone crusher chamber, the two processes of rock flow and rock breakage may be decoupled. Consequently, this study firstly characterised the flow behaviour of broken rock through a static crusher chamber by conducting a series of experiments to investigate the flow of regular river pebbles down an inclined chute. A parallel computational study constructed and solved a series of DEM models to replicate the results of these experimental studies. An analysis of the results of these studies concluded that an accurate model replication of the shape of the pebbles and the method used to load the pebbles into the inclined chute were important to ensure that the DEM models successfully reproduced the observed particle flow behaviour. These studies also established relationships between the chute geometry and the time taken for the loaded pebble streams to clear the chute. To investigate the rock breakage behaviour observed within a cone crusher chamber, thirty quasi-spherical particles of Glensanda ballast aggregate were diametrically crushed in the laboratory using a Zwick crushing machine. The crushed rock particles used were of three sieve size fractions: 14-28mm, 30-37.5mm and 40-60mm. The effects that either a variation in the particle size or strength has on and the number and size distribution of the progeny rock fragments produced on breakage were studied. Subsequently, a series of DEM simulation models were constructed and solved to replicate the experimental results obtained from these crushing tests. The aggregate particles were represented by agglomerates consisting of a number of smaller diameter bonded micro-spheres. A new method was proposed to generate a dense, isotropic agglomerate with negligible initial overlap between the micro-spheres by inserting particles to fill the voids in the agglomerate. In addition, the effects that a variation in the particle packing configurations had on the simulated strength and breakage patterns experienced by the model agglomerate rock particles were investigated. The results from these DEM model studies were validated against the experimental data obtained from the ballast rock breakage tests. A comparative analysis of the experimental and modelling studies concluded that once the bond strengths between the constituent micro-spheres matched the values determined from the rock breakage tests, then the numerical models were able to replicate the measured variations in the aggregate particle strengths. Finally, the individual validated DEM aggregate particle flow and breakage modes were combined to construct a preliminary coupled prototype DErvl model to simulate the flow and breakage of an aggregate feed through a cone crusher chamber. The author employed two modelling approaches: the population balance model (PBM) and bonded particle model (BPM) to simulate the observed particle breakage characteristics. The application of the PBM model was successfully validated against historical experimental data available in the literature. However, the potential wider use of the BPM model was deemed impractical due to the high computation time. From a comparative analysis of the particle size distributions of the feed and computed product streams by the two modelling approaches, it is concluded that the simpler PBM produces more practical computationally efficient numerical solutions.

DEM Simulation of an Impact Crusher Using the Fast-Cutting Breakage Model

Discrete Element Modeling of the Breakage of Single Polyhedral Particles in the Rotary Offset Crusher

Dynamic Analysis of Tip Set Extra Hard Load of Vertical Shaft Impact Crusher

Discrete Element Method (DEM) Modelling of Rock Flow and Breakage Within a Cone Crusher

Study on Main Butt Ends Load of Vertical Shaft Impact Crusher

An Impact Energy Erosion Model with an Energy Allocation Rule for the Discrete Element Method

A combined experimental and DEM approach to determine the breakage of particles in an impact mill

Crushing Product Size-reduction Analysis of Compressing Crusher

The Crushing Distribution Morphology of a Single Particle Subjected to Rotary Impact

Analysis and Optimization of Vibration Characteristics of Gyratory Crusher Based on DEM-MBD and PSO

Research on the Load Distribution of Throwing Ends in Vertical Shaft Impact Crusher

Discrete Element Modelling of A Rock Cone Crusher

An improved model for predicting the erosion within the DEM framework

Collision Energy Analysis within the Vertical Shaft Impact Crusher Based on the Computational Fluid Dynamics-Discrete Element Method

Determining Digital Representation and Representative Elementary Volume Size of Broken Rock Mass Using the Discrete Fracture Network–Discrete Element Method Coupling Technique

Crushing characteristics and performance evaluation of iron ore in a cone crusher: A numerical study

An improved breakage model with a fast-cutting method for simulating the breakage of polyhedral particles

Development of a DEM Method for Predicting Wear Distribution on Particle Scale

Mathematical Modeling of Particle Size and Particle Shape of Crushing Quality for Cone Crusher

Application of Multibody Dynamics and Bonded-Particle GPU Discrete Element Method in Modelling of a Gyratory Crusher

Establishing an Oblique Impact Breakage Master Curve Using a DEM Bonded Contact Model